TT CME Gateway System Administration Manual - Trading ...
TT CME Gateway System Administration Manual - Trading ...
TT CME Gateway System Administration Manual - Trading ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
7<br />
Using Connection Quality Tools<br />
<strong>CME</strong> <strong>Gateway</strong> <strong>System</strong> <strong>Administration</strong> <strong>Manual</strong> 119<br />
<strong>Trading</strong> Technologies International, Inc.<br />
Troubleshooting<br />
Overview For the MDP connection, the <strong>CME</strong> <strong>Gateway</strong> receives FIX/FAST messages via two<br />
connections labeled Feed A and Feed B. The Connection Quality Tools help<br />
troubleshoot and prevent problems associated with downed or improperly<br />
connected feeds.<br />
There are two Connection Quality Tools available:<br />
• <strong>TT</strong> FAST Tester - quickly checks the standard MDP connection (Feeds A<br />
and B) between the <strong>CME</strong> <strong>Gateway</strong> and the exchange.<br />
• <strong>TT</strong> Bandwidth Tester - checks the standard MDP connection (Feed A and B)<br />
for packet loss and latency.<br />
Before You Begin You can start the <strong>TT</strong> FAST Tester and <strong>TT</strong> Bandwidth Tester by double-clicking the<br />
executable file (.exe.) located in the :tt\Exchange-Flavor<br />
directory. The filenames are tt_fast_tester.exe and tt_fast_bandwidth.exe.<br />
Before starting each test, you must edit the following in the hostinfo.cfg file:<br />
• Configure the [price_session] section with your custom connection<br />
values.<br />
• Add the <strong>CME</strong> Group-facing NIC to each NetworkInterface parameter.<br />
• Create a copy of the hostinfo.cfg file with the name <strong>CME</strong>Hostinfo.cfg. The<br />
<strong>TT</strong> FAST Tester and <strong>TT</strong> Bandwidth Tester use the settings in this file to<br />
verify connectivity.<br />
Executing the Tests The <strong>TT</strong> FAST Tester runs a test for each channel along the NIC (Network Interface<br />
Card) defined in the hostinfo.cfg file. The utility checks the heartbeat the<br />
exchange sends at least every 60 seconds. Therefore, each channel test may take<br />
up to 65 seconds. For more info on Heartbeating, refer to “Aconfig and<br />
Environment Setup” in the <strong>TT</strong> <strong>Gateway</strong>s Architecture <strong>System</strong> <strong>Administration</strong><br />
<strong>Manual</strong> Version 7.X.<br />
In addition to testing the overall status of the connection, the <strong>TT</strong> Bandwidth Tester<br />
also checks for packet loss and packet latency. Due to the extensive nature of this<br />
test, the utility runs for approximately one hour. If stopped before completion, the<br />
utility can fail to create a proper log file.<br />
To run a test, double-click its executable. Once complete, the MDP Quality Tools<br />
create the log files tt_fast_tester.out and tt_fast_bandwidth.out in the<br />
:tt\logfiles directory.<br />
<strong>TT</strong> FAST Tester Results The following illustrates the results the <strong>TT</strong> FAST Tester writes to the<br />
tt_fast_tester.out logfile:<br />
To interpret the <strong>TT</strong> FAST Tester results:<br />
1. The utility prints out information regarding which NICs (Network Interface<br />
Cards) it tests.<br />
Example:<br />
Interface: feeda using 172.20.16.210<br />
Interface: feedb using 172.20.28.138