1. D-BACS - Daikin

More documents

Recommendations

Info

5.2 Points of Installation intelligent Touch Controller (Do not fail to use a round crimp terminal with reinforcing sleeve for safety wiring connection to the intelligent Touch Controller.) When wiring, cut off the power supply (using a local switch) and do not apply power until all work has been finished. Wiring for power supply and Connecting wiring for DIII-NET communication of indoor units In order to perform centralized control of indoor units using this controller, connect the power wiring to terminals L and N, earth wire to earth terminal and connecting wiring for DIII-NET communication of air-conditioner (indoor unit and outdoor unit) to terminals F1 and F2 respectively as shown in the sketch below. Outdoor unit OUT-OUT IN-OUT F1, F2F1, F2 Outdoor unit OUT-OUT IN-OUT F1, F2F1, F2 Power cable wiring Fuse COM Di1 Pi3 COM Pi2 Pi1 F2 F1 Indoor unit F1, F2 N, P F1, F2 N, P Indoor unit F1, F2 N, P Connecting wiring for D -NET communication of indoor and outdoor units F1, F2 N, P 1.25mm 2 Indoor unit Indoor unit Grounding work Indoor unit F1, F2 N, P Up to 16 units maximum Indoor unit F1, F2 N, P N L ~ 100-240V Fuse (10A) Maximum up to 64 groups (128 units) 5.2 Points of Installation 105 switch Indoor unit F1, F2 N, P Indoor unit F1, F2 N, P Power supply 100V-240V ~ 50/60Hz F1, F2 N, P F1, F2 N, P 0.75 - 1.25mm2 10A vinyl cord or cable with sheath (2 wire) ---Up to 1000m maximum (wiring length -- up to 2000m maximum) (When shield cable is used, the wiring length is available up to 1500m.) For the type of electric wire, refer to the design guide. Indoor unit Indoor unit > Don't fail to perform installation of Grounding work. Don't connect the grounding wire to any of gas pipe, city water pipe, lightning rod, and telephone grounding wire. Don't turn ON the power supply (front switch) until all the works are complete. The connecting wiring for communication of indoor and outdoor units is a connecting wiring for the control. Don't clamp these cables together with high voltage cables. Failure to observe this instruction would cause control error. Don't connect the power cable to F1, F2 terminal blocks. Wrong connection to these terminal blocks could result in damage and burning of the centralized control devices and of the electric parts of the indoor and outdoor units. This is very hazardous. Check each wired cable once more before turning ON the power switch.
intelligent Touch Controller 5.3 Wiring for Force Stop Input and for Electric Power Distribution In order to stop the air-conditioner through force stop input, connect the wiring for force stop input to the terminals Di1 and COM as shown in the sketch below. In addition, in order to calculate the electric energy using optional Power Proportional Distribution software, connect the wiring for electric energy to the terminals Pi and COM as shown in the sketch below. LAN Forced OFF contact input COM Di1 Pi3 COM Pi2 Pi1 F2 F1 N L ~ 100-240V Measuring meter (max 3 units) (When using an optional Power Proportional Distribution function) Wiring for force stop input 0.75 - 1.25mm 2 vinyl cord or cable with sheath (2 wire) -- up to 150m maximum When FORCE-STOP INPUT is kept ON, the indoor units connected thereto are unable to be operated because they are force-stopped. Use a contact which can guarantee minimum application load DC16V and 10mA. Use an instantaneous contact of 200msec or more in current feed time, where required. Meter wiring for power distribution (option) 0.75 - 1.25mm 2 vinyl cord or cable with sheath (2 wire) -- up to 150m maximum The number of connectable indoor units is up to 64 units maximum, where the Power Proportional Distribution Card as option is used. The measuring meters to be connected must meet the requirements specified below. To be a measuring meter with pulse oscillator. (pulse/kwh) Pulse band of 100msec or mores Measuring meter which uses semiconductor relay for pulse output and outputs pulses from non-voltage contact > Don't clamp these cables together with high voltage cables. Failure to observe this instruction would cause control error. Terminals COM are inter-connected. Connecting to either one is allowed, but the number of cables connectable to one terminal is limited to 2 pieces. Don't connect the power cable to Pi, Di, COM terminal blocks. Wrong connection to these terminal blocks could result in damage and burning of the centralized control devices and of the electric parts of the indoor and outdoor units. This is very hazardous. Check each wired cable once more before turning ON the power switch. 106 5.3 Wiring for Force Stop Input and for Electric Power Distribution � �
Page 1 and 2:
ED 72 - 721 Daikin Buildings Air-c
Page 3 and 4:
ii 6. Group and Zone...............
Page 5 and 6:
iv 2. Unified ON/OFF Controller ..
Page 7 and 8:
vi 12. Control-related Design Keypo
Page 9 and 10:
Introduction 1. Introduction 1.1 DA
Page 11 and 12:
Introduction 1.3 How to Use this Do
Page 13 and 14:
Introduction Term Explanation D-BAC
Page 15 and 16:
Introduction Term Explanation NI Th
Page 17 and 18:
Introduction xvi 1.5 Open Network G
Page 19 and 20:
Outline of D-BACS System 1. D-BACS
Page 21 and 22:
Outline of D-BACS System 2. System
Page 23 and 24:
Outline of D-BACS System 3. List of
Page 25 and 26:
Outline of D-BACS System 3.2 Main S
Page 27 and 28:
Outline of D-BACS System Central Co
Page 29 and 30:
Outline of D-BACS System Control Me
Page 31 and 32:
Outline of D-BACS System 4. List of
Page 33 and 34:
Outline of D-BACS System 16 DIII :
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Outline of D-BACS System 6. Central
Page 41 and 42:
Outline of D-BACS System 24
Page 43 and 44:
Fundamental of DIII-NET 1. Design o
Page 45 and 46:
Fundamental of DIII-NET 2.3 Connect
Page 47 and 48:
Fundamental of DIII-NET [Bad Exampl
Page 49 and 50:
Fundamental of DIII-NET 2.3.3 Wirin
Page 51 and 52:
Fundamental of DIII-NET 3. Wiring L
Page 53 and 54:
Fundamental of DIII-NET 5. Number o
Page 55 and 56:
Fundamental of DIII-NET 5.3 Number
Page 57 and 58:
Fundamental of DIII-NET 6. Group an
Page 59 and 60:
Fundamental of DIII-NET 6.4 Setting
Page 61 and 62:
Fundamental of DIII-NET 6.4.3 Simpl
Page 63 and 64:
Fundamental of DIII-NET Initial set
Page 65 and 66:
Fundamental of DIII-NET 7. Wiring S
Page 67 and 68:
Fundamental of DIII-NET Qty. 1 1 1
Page 69 and 70:
Fundamental of DIII-NET 8.3 Combina
Page 71 and 72: Fundamental of DIII-NET 8.4 Sequent
Page 73 and 74: Remote Controllers 1. List of Indoo
Page 75 and 76: Remote Controllers 2. Dimensions of
Page 77 and 78: Remote Controllers FXD(Q), FXS(Q),
Page 79 and 80: Remote Controllers 2.3 Simplified R
Page 81 and 82: Remote Controllers 3. Functions of
Page 83 and 84: Remote Controllers 3.3.2 Name and F
Page 87 and 88: Remote Controllers 3.6 Wired Remote
Page 89 and 90: Remote Controllers 3.7 Wireless Rem
Page 91 and 92: Remote Controllers � Example of t
Page 93 and 94: Remote Controllers 4. Various Contr
Page 95 and 96: Remote Controllers 4.4 Remote Contr
Page 97 and 98: Remote Controllers 4.5 Remote Sens
Page 99 and 100: Remote Controllers 5. Field Setting
Page 101 and 102: Remote Controllers Applicable range
Page 105 and 106: Remote Controllers 5.4 HRV 4, 5 3
Page 107 and 108: Remote Controllers 90 5.4 HRV
Page 109 and 110: intelligent Touch Controller 1. Par
Page 111 and 112: intelligent Touch Controller Displa
Page 117 and 118: intelligent Touch Controller 3. Spe
Page 119 and 120: intelligent Touch Controller Centra
Page 121: intelligent Touch Controller 5. Ele
Page 125 and 126: intelligent Touch Controller 5.6 DI
Page 127 and 128: intelligent Touch Controller � Ho
Page 129 and 130: intelligent Touch Controller 5.9.2
Page 135 and 136: intelligent Touch Controller 118
Page 137 and 138: intelligent Touch Controller 120
Page 139: intelligent Touch Controller 122 Ti
show all

1. D-BACS - Daikin

Create successful ePaper yourself

Delete template?

Save as template?