Hybrid Restorations with the CAMLOG Implant System (PDF

More documents

Recommendations

Info

HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM BAR RESTORATIONS Gingival heights from the implant shoulder support to the bar abutment plateau The gingival height is the distance from the bar abutment plateau to the highest point of the surrounding gingiva. The bar abutment plateau should be approx. 0.5 mm supragingival. PROSTHETIC SCREWS FOR BAR ABUTMENT, HEX All bar bases are attached with prosthetic screws for bar abutment, hex, to the CAMLOG ® bar abutments. New unused prosthetic screws are used for final insertion. ART. NO. J4005.1602 J4005.2002 Thread M 1.6 for bar abutment M 2.0 for bar abutment Ø 3.3/3.8/4.3 mm Ø 5.0/6.0 mm Def. torque for insertion of the bar framework: 15 Ncm Abutments must be retightened to the same torque after about five minutes to reach the maximum retaining screw tension. This prevents screws from loosening. The prosthetic screws are only hand-tightened on the working cast. 22 0.5 mm 0.5 mm 2 mm 4 mm
CAMLOG ® IMPRESSION TAKING OPTIONS After successful implant insertion, the impression can be taken in two versions: IMPRESSION TAKING OVER CAMLOG ® BAR ABUTMENTS: Impression taking after final insertion of the CAMLOG ® bar abutments with impression posts for bar abutment. The cast is then fabricated with soldering aid/bar lab analogs. IMPRESSION TAKING OVER CAMLOG ® IMPLANT SHOULDER: Impression taken over the CAMLOG ® implant shoulder directly with CAMLOG ® impression posts, open or closed tray, before insertion of CAMLOG ® bar abutments. The cast is then fabricated with CAMLOG ® lab analogs. See also page 13–15 and working instruction "Impression taking, bite registration and temporary restoration on CAMLOG ® implants", Art. No. J8000.0065. Driver for bar abutment Ø 3.3/3.8/4.3 mm Ø 5.0/6.0 mm HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM IMPRESSION TAKING OVER CAMLOG ® BAR ABUTMENTS INSERTION OF CAMLOG ® BAR ABUTMENTS After successful implant insertion and determination of the appropriate gingival height, the CAMLOG ® bar abutments are inserted into the CAMLOG ® implants. The abutments are inserted into the driver for bar abutments. A driver is available for each implant diameter 3.3/3.8/4.3 mm and 5.0/6.0 mm. A screw integrated in the instrument secures the abutment. The screw is tightened by hand. Bar abutment/instrument connection The CAMLOG ® bar abutments are inserted into the previously cleaned CAMLOG ® implants and the torque wrench is then used to tighten the abutments definitely in the implants based on the specified tightening torque. TIGHTENING TORQUE FOR CAMLOG ® BAR ABUTMENTS Ø 3.3 mm 20 Ncm Ø 3.8/4.3/5.0/6.0 mm 30 Ncm CAMLOG ® abutments must be retightened to the same torque after about five minutes to reach the maximum screw tension. This prevents screws from loosening to the extent possible. 23
Page 1 and 2: HYBRID RESTORATIONS WITH THE CAMLOG
Page 3 and 4: LOCATOR ® ANCHORING SYSTEM PRODUCT
Page 5 and 6: SYSTEM INTRODUCTION GENERAL GUIDELI
Page 9 and 10: CAMLOG COLOR-CODING HYBRID RESTORAT
Page 11 and 12: ANCHORING OPTIONS In consideration
Page 13 and 14: CAMLOG ® CAST FABRICATION CAST FAB
Page 15 and 16: CAST FABRICATION, OPEN TRAY PREPARA
Page 17 and 18: CAMLOG ® BITE REGISTRATION POSTS I
Page 19 and 20: Remove the bite register, the bite
Page 21: BAR RESTORATIONS INTRODUCTION In im
Page 25 and 26: The impression posts are then reatt
Page 27 and 28: IMPRESSION TAKING OVER THE CAMLOG
Page 29 and 30: INVESTMENT, CAST AND DEVESTMENT The
Page 31 and 32: TRIMMING After devestment and clean
Page 33 and 34: After wax-up of the bar framework,
Page 35 and 36: INSERTING THE BAR CONSTRUCTION The
Page 37 and 38: RELINING OF A BAR-SUPPORTED FULL DE
Page 39 and 40: BALL ABUTMENT ANCHORING SYSTEM INTR
Page 41 and 42: CAMLOG ® BALL ABUTMENT FOR IMPLANT
Page 43 and 44: FABRICATION OF A NEW BALL ABUTMENT-
Page 45 and 46: BONDING THE MATRICES IN THE METAL R
Page 47 and 48: BROADENING OF AN EXISTING FULL DENT
Page 49 and 50: A cold-cured polymer is used to att
Page 51 and 52: RELINING NOTE Before relining, the
Page 55 and 56: PROCESSING INSERTION OF THE CAMLOG
Page 57 and 58: CAST FABRICATION After taking the i
Page 59 and 60: CONVERTING AN EXISTING FULL DENTURE
Page 61 and 62: The titanium housing is polymerized
Page 63 and 64: DOUBLE CROWN RESTORATIONS INTRODUCT
Page 65 and 66: CAMLOG ® UNIVERSAL ABUTMENT AND CA
Page 67 and 68: FABRICATING A TERTIARY FRAMEWORK FO
Page 69 and 70: CAMLOG ® GOLD-PLASTIC ABUTMENT The
Page 71 and 72: The investment material must be mat
Page 73 and 74:
ACCESSORIES AND PROSTHETIC INSTRUME
Page 75 and 76:
FURTHER DOCUMENTATION Further infor
show all

Hybrid Restorations with the CAMLOG Implant System (PDF

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?