Hybrid Restorations with the CAMLOG Implant System (PDF

More documents

Recommendations

Info

HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM LOCATOR ® ANCHORING SYSTEM PRODUCT DESCRIPTION The Locator ® anchoring system is intended for use in the tissue-borne and implant-retained prosthesis for resilient supported full dentures in the maxilla and mandible. The system can be used with implant divergences of up to 20° per implant (3.3 mm diameter CAMLOG ® Locator ® abutment – up to 10° divergence per implant). The self-aligning design of the Locator ® anchoring system supports the patient when inserting and seating the prosthesis. The design of the CAMLOG ® Locator ® abutment and replacement males provide double (dual) retention. The Locator ® anchoring system contains various replacement males with different retention forces. The CAMLOG ® Locator ® abutments are available for implant diameters 3.3 mm in three gingival heights (1.0, 2.0 and 3.0 mm), and for implant diameters 3.8, 4.3 and 5.0 mm in four gingival heights (1.0, 2.0, 3.0 and 4.0 mm). 52 High functional area 1.52 mm Gingival height CAMLOG ® implant Diameter of the functional area 3.8 mm Dual retention Dual retention by a stamp in the replacement males and circular undercut of the CAMLOG ® Locator ® abutment CAMLOG ® Locator ® abutment The Locator ® anchoring system can also be integrated in a full denture supported on CAMLOG ® implants: • For the fabrication of a new full denture with Locator ® retention components • Converting an existing full denture into a Locator ® -retained denture
HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM LOCATOR ® SYSTEM COMPONENTS Art. No. Article Implant Ø in mm GH in mm J2253.3310 J2253.3320 J2253.3330 J2253.3810 J2253.3820 J2253.3830 J2253.3840 J2253.4310 J2253.4320 J2253.4330 J2253.4340 J2253.5010 J2253.5020 J2253.5030 J2253.5040 J2253.0200 J2253.0340 J2253.0350 J2253.0102 J2253.0112 J2253.0401 J2253.0402 J2253.1005 J2253.1003 J2253.1002 J2253.2004 J2253.2003 J2253.2002 CAMLOG ® Locator ® abutment CAMLOG ® Locator ® abutment CAMLOG ® Locator ® abutment CAMLOG ® Locator ® abutment Locator ® impression cap Locator ® analog Locator ® analog Locator ® block out spacer Locator ® processing replacement male Locator ® replacement male, clear, STRONG, Div.: 0°–10° Locator ® replacement male, pink, MEDIUM, Div.: 0°–10° Locator ® replacement male, blue, LIGHT, Div.: 0°–10° Locator ® replacement male for extended range, green, STRONG, Div.: 10°–20° Locator ® replacement male for extended range, orange, MEDIUM, Div.: 10°–20° Locator ® Locator replacement male for extended range, red, LIGHT, Div.: 10°–20° ® male processing packages (2 units) Content per package: 1 Titanium housing with processing replacement male, 1 Block out spacer white, 1 Replacement male clear, 1 Replacement male pink, 1 Replacement male blue Locator ® 3.3/3.8/4.3/5.0 male processing packages for ex- 3.8/4.3/5.0 tended range (2 units), Content per package: 1 Titanium housing with processing replacement male, 1 Block out spacer white, 1 Replacement male green, 1 Replacement male orange, 1 Replacement male red 3.3/3.8/4.3/5.0 3.3/3.8/4.3/5.0 3.3 3.8 4.3 5.0 3.3/3.8/4.3/5.0 3.3/3.8/4.3 5.0 1.0 2.0 3.0 1.0 2.0 3.0 4.0 1.0 2.0 3.0 4.0 1.0 2.0 3.0 4.0 53
Page 1 and 2: HYBRID RESTORATIONS WITH THE CAMLOG
Page 3 and 4: LOCATOR ® ANCHORING SYSTEM PRODUCT
Page 5 and 6: SYSTEM INTRODUCTION GENERAL GUIDELI
Page 7 and 8: HYBRID RESTORATIONS WITH THE CAMLOG
Page 9 and 10: CAMLOG COLOR-CODING HYBRID RESTORAT
Page 11 and 12: ANCHORING OPTIONS In consideration
Page 13 and 14: CAMLOG ® CAST FABRICATION CAST FAB
Page 15 and 16: CAST FABRICATION, OPEN TRAY PREPARA
Page 17 and 18: CAMLOG ® BITE REGISTRATION POSTS I
Page 19 and 20: Remove the bite register, the bite
Page 21 and 22: BAR RESTORATIONS INTRODUCTION In im
Page 23 and 24: CAMLOG ® IMPRESSION TAKING OPTIONS
Page 25 and 26: The impression posts are then reatt
Page 27 and 28: IMPRESSION TAKING OVER THE CAMLOG
Page 29 and 30: INVESTMENT, CAST AND DEVESTMENT The
Page 31 and 32: TRIMMING After devestment and clean
Page 33 and 34: After wax-up of the bar framework,
Page 35 and 36: INSERTING THE BAR CONSTRUCTION The
Page 37 and 38: RELINING OF A BAR-SUPPORTED FULL DE
Page 39 and 40: BALL ABUTMENT ANCHORING SYSTEM INTR
Page 41 and 42: CAMLOG ® BALL ABUTMENT FOR IMPLANT
Page 43 and 44: FABRICATION OF A NEW BALL ABUTMENT-
Page 45 and 46: BONDING THE MATRICES IN THE METAL R
Page 47 and 48: BROADENING OF AN EXISTING FULL DENT
Page 49 and 50: A cold-cured polymer is used to att
Page 51: RELINING NOTE Before relining, the
Page 55 and 56: PROCESSING INSERTION OF THE CAMLOG
Page 57 and 58: CAST FABRICATION After taking the i
Page 59 and 60: CONVERTING AN EXISTING FULL DENTURE
Page 61 and 62: The titanium housing is polymerized
Page 63 and 64: DOUBLE CROWN RESTORATIONS INTRODUCT
Page 65 and 66: CAMLOG ® UNIVERSAL ABUTMENT AND CA
Page 67 and 68: FABRICATING A TERTIARY FRAMEWORK FO
Page 69 and 70: CAMLOG ® GOLD-PLASTIC ABUTMENT The
Page 71 and 72: The investment material must be mat
Page 73 and 74: ACCESSORIES AND PROSTHETIC INSTRUME
Page 75 and 76: FURTHER DOCUMENTATION Further infor

Hybrid Restorations with the CAMLOG Implant System (PDF

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?