Hybrid Restorations with the CAMLOG Implant System (PDF

More documents

Recommendations

Info

HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM BALL ABUTMENT ANCHORING SYSTEM INSERTION OF THE CAMLOG ® BALL ABUTMENT AND THE PROSTHESIS After removing the CAMLOG ® healing cap, the CAMLOG ® ball abutments are transferred from the working cast to the previously cleaned CAMLOG ® implant and the driver for ball abutment and the torque wrench are used to tighten the abutments in the implants based on the specified tightening torque. TIGHTENING TORQUE FOR CAMLOG ® BALL ABUTMENTS Ø 3.3 mm 20 Ncm Ø 3.8/4.3/5.0 mm 30 Ncm CAMLOG ® abutments must be retightened with the same torque after about five minutes to reach the maximum screw tension. This prevents screws from loosening to the extent possible. The screwdriver/activator for ball abutment matrix is used to set the required retention force of the lamella retention inserts and the prosthesis is inserted in the patient's mouth. 46 IMPORTANT NOTE Do not place the stabilizing ring in the mouth. The clinical insertion is completed with a check of the occlusion and articulation.
BROADENING OF AN EXISTING FULL DENTURE INTO A BALL ABUTMENT-RETAINED FULL DENTURE An existing mucosa-supported full denture can be converted into a ball abutment-retained prosthesis in principle, but this will weaken the prosthesis. Because it is known that the chewing force increases with implant- retained dentures, the denture can fracture without metal reinforcement. This procedure can only be considered as a temporary solution. SELECTION AND INSERTION OF THE CAMLOG ® BALL ABUTMENTS After the CAMLOG ® implants have healed, the CAMLOG ® ball abutments are inserted. In conformance with the specified implant diameters and gingival heights, the clinician selects the CAMLOG ® ball abutments intraorally and uses the driver for ball abutment to screw them into the previously cleaned CAMLOG ® implants. Information about torques, see page 46. Different abutment heights can be selected to compensate for differences in levels in the gingival margin and implants. The ball heads should be at a uniform level for the best possible retention effect. The ball abutment plateau should be approx. 1 mm supragingival. IMPRESSION TAKING OF THE CAMLOG ® BALL ABUTMENTS The impression is taken over the CAMLOG ® ball abutments directly without accessories. The CAMLOG ® ball abutments must be fully overmolded and integrated with impression material. Silicone or polyether are suitable impression materials. HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM 1mm 47
Page 1 and 2: HYBRID RESTORATIONS WITH THE CAMLOG
Page 3 and 4: LOCATOR ® ANCHORING SYSTEM PRODUCT
Page 5 and 6: SYSTEM INTRODUCTION GENERAL GUIDELI
Page 9 and 10: CAMLOG COLOR-CODING HYBRID RESTORAT
Page 11 and 12: ANCHORING OPTIONS In consideration
Page 13 and 14: CAMLOG ® CAST FABRICATION CAST FAB
Page 15 and 16: CAST FABRICATION, OPEN TRAY PREPARA
Page 17 and 18: CAMLOG ® BITE REGISTRATION POSTS I
Page 19 and 20: Remove the bite register, the bite
Page 21 and 22: BAR RESTORATIONS INTRODUCTION In im
Page 23 and 24: CAMLOG ® IMPRESSION TAKING OPTIONS
Page 25 and 26: The impression posts are then reatt
Page 27 and 28: IMPRESSION TAKING OVER THE CAMLOG
Page 29 and 30: INVESTMENT, CAST AND DEVESTMENT The
Page 31 and 32: TRIMMING After devestment and clean
Page 33 and 34: After wax-up of the bar framework,
Page 35 and 36: INSERTING THE BAR CONSTRUCTION The
Page 37 and 38: RELINING OF A BAR-SUPPORTED FULL DE
Page 39 and 40: BALL ABUTMENT ANCHORING SYSTEM INTR
Page 41 and 42: CAMLOG ® BALL ABUTMENT FOR IMPLANT
Page 43 and 44: FABRICATION OF A NEW BALL ABUTMENT-
Page 45: BONDING THE MATRICES IN THE METAL R
Page 49 and 50: A cold-cured polymer is used to att
Page 51 and 52: RELINING NOTE Before relining, the
Page 55 and 56: PROCESSING INSERTION OF THE CAMLOG
Page 57 and 58: CAST FABRICATION After taking the i
Page 59 and 60: CONVERTING AN EXISTING FULL DENTURE
Page 61 and 62: The titanium housing is polymerized
Page 63 and 64: DOUBLE CROWN RESTORATIONS INTRODUCT
Page 65 and 66: CAMLOG ® UNIVERSAL ABUTMENT AND CA
Page 67 and 68: FABRICATING A TERTIARY FRAMEWORK FO
Page 69 and 70: CAMLOG ® GOLD-PLASTIC ABUTMENT The
Page 71 and 72: The investment material must be mat
Page 73 and 74: ACCESSORIES AND PROSTHETIC INSTRUME
Page 75 and 76: FURTHER DOCUMENTATION Further infor

Hybrid Restorations with the CAMLOG Implant System (PDF

Create successful ePaper yourself

Delete template?

Save as template?