Hybrid Restorations with the CAMLOG Implant System (PDF

More documents

Recommendations

Info

HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM DOUBLE CROWN RESTORATIONS For fabrication of double crowns using the electroplating technique, the manufacturer's specifications must be observed. The preparation for the cast fabrication of double crowns occurs similar to the cone-telescopic crown technique. To prevent the caps from rotating, the abutments are lightly ground in oval form. The surface must be homogeneous. The space for the tertiary framework required to receive the secondary crowns can be tested at every phase of preparation with the silicone index with the denture teeth in position. FABRICATING SECONDARY COPINGS The secondary crowns or superstructure are then fabricated. The tensionfree seat of the superstructure is of paramount importance for the longterm success of an implant-prosthetic restoration. We recommend bonding the secondary copings intraorally into the tertiary framework (passive fit). 72 NOTES Electroformed secondary copings Electroforming is conducted as specified by the manufacturer. The CAMLOG ® abutments are inserted into a CAMLOG ® lab analog of the appropriate diameter and fixed with a CAMLOG ® lab screw. The thickness should be 0.2–0.3 mm. The special feature of the low layer thickness of the electroformed components and the resulting low stability of the secondary coping prevent direct polymerization in the acrylic denture base. For this reason, a tertiary framework must be fabricated over the secondary copings for reinforcement. Cast secondary copings The wall thickness of the secondary copings should be approx. 0.5 mm. Fabrication is similar to standard crown and bridge technique. CAUTION Do not mix up the CAMLOG ® abutments and secondary copings! We recommend a color buccal marker on the abutment, coping and working cast. For information about "Fabricating a tertiary framework for double crown restorations", "Bonding of the secondary coping intraorally" and "Insertion of the prosthetic restoration", see pages 67–68.
ACCESSORIES AND PROSTHETIC INSTRUMENTS HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM CAMLOG ® LAB ANALOGS FOR CAST FABRICATION Art. No. J3010.3300 J3010.3800 J3010.4300 J3010.5000 J3010.6000 Ø mm 3.3 3.8 4.3 5.0 6.0 CAMLOG ® LAB SCREWS (HEX) FOR SECURING CAMLOG ® ABUTMENTS TO THE CAST Art. No. Article J4006.1601 CAMLOG ® lab screw (hex), brown anodized, Thread M 1.6, for implant diameters 3.3/3.8/4.3 mm J4006.2001 CAMLOG ® lab screw (hex), brown anodized, Thread M 2.0, for implant diameters 5.0/6.0 mm SCREWDRIVER, HEX Art. No. Article J5316.0510 Screwdriver (hex), extra short J5316.0501 Screwdriver (hex), short J5316.0502 Screwdriver (hex), long UNIVERSAL HOLDER Art. No. Article J3709.0010 Universal holder, incl. 2 CAMLOG ® lab screws (thread M 1.6 and M 2.0) and each 1 CAMLOG ® abutment collect for implant diameters 3.3/3.8/4.3/5.0/6.0 mm J3709.0015 Universal holder REAMER FOR DILATING THE PLASTER MODEL, FOR UNIVERSAL HOLDER, incl. color-coded guide pin Art.-Nr. J3706.3300 J3706.3800 J3706.4300 J3706.5000 J3706.6000 Ø mm 3.3 3.8 4.3 5.0 6.0 REWORKING REAMER, FOR BASE FOR BAR ABUTMENTS Art. No. Article J3711.0010 Plane surface/cone seat, burn-out for implant diameters 3.3/3.8/4.3 mm J3711.0015 Plane surface/cone seat, burn-out for implant diameters 5.0/6.0 mm J3711.0020 Screw seat, burn-out for implant diameters 3.3/3.8/4.3 mm J3711.0025 Screw seat, burn-out for implant diameters 5.0/6.0 mm 73
Page 1 and 2:
HYBRID RESTORATIONS WITH THE CAMLOG
Page 3 and 4:
LOCATOR ® ANCHORING SYSTEM PRODUCT
Page 5 and 6:
SYSTEM INTRODUCTION GENERAL GUIDELI
Page 7 and 8:
HYBRID RESTORATIONS WITH THE CAMLOG
Page 9 and 10:
CAMLOG COLOR-CODING HYBRID RESTORAT
Page 11 and 12:
ANCHORING OPTIONS In consideration
Page 13 and 14:
CAMLOG ® CAST FABRICATION CAST FAB
Page 15 and 16:
CAST FABRICATION, OPEN TRAY PREPARA
Page 17 and 18:
CAMLOG ® BITE REGISTRATION POSTS I
Page 19 and 20:
Remove the bite register, the bite
Page 21 and 22: BAR RESTORATIONS INTRODUCTION In im
Page 23 and 24: CAMLOG ® IMPRESSION TAKING OPTIONS
Page 25 and 26: The impression posts are then reatt
Page 27 and 28: IMPRESSION TAKING OVER THE CAMLOG
Page 29 and 30: INVESTMENT, CAST AND DEVESTMENT The
Page 31 and 32: TRIMMING After devestment and clean
Page 33 and 34: After wax-up of the bar framework,
Page 35 and 36: INSERTING THE BAR CONSTRUCTION The
Page 37 and 38: RELINING OF A BAR-SUPPORTED FULL DE
Page 39 and 40: BALL ABUTMENT ANCHORING SYSTEM INTR
Page 41 and 42: CAMLOG ® BALL ABUTMENT FOR IMPLANT
Page 43 and 44: FABRICATION OF A NEW BALL ABUTMENT-
Page 45 and 46: BONDING THE MATRICES IN THE METAL R
Page 47 and 48: BROADENING OF AN EXISTING FULL DENT
Page 49 and 50: A cold-cured polymer is used to att
Page 51 and 52: RELINING NOTE Before relining, the
Page 53 and 54: HYBRID RESTORATIONS WITH THE CAMLOG
Page 55 and 56: PROCESSING INSERTION OF THE CAMLOG
Page 57 and 58: CAST FABRICATION After taking the i
Page 59 and 60: CONVERTING AN EXISTING FULL DENTURE
Page 61 and 62: The titanium housing is polymerized
Page 63 and 64: DOUBLE CROWN RESTORATIONS INTRODUCT
Page 65 and 66: CAMLOG ® UNIVERSAL ABUTMENT AND CA
Page 67 and 68: FABRICATING A TERTIARY FRAMEWORK FO
Page 69 and 70: CAMLOG ® GOLD-PLASTIC ABUTMENT The
Page 71: The investment material must be mat
Page 75 and 76: FURTHER DOCUMENTATION Further infor
show all

Hybrid Restorations with the CAMLOG Implant System (PDF

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?