Hybrid Restorations with the CAMLOG Implant System (PDF

More documents

Recommendations

Info

HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM LOCATOR ® ANCHORING SYSTEM The titanium housing is attached by the black processing replacement male and the resilience of the denture determined. 60 Titanium housing with black processing replacement male CAUTION Undercuts between the titanium housings and the surrounding tissue not covered by the block out spacers must be blocked out. Acrylic must not get into the titanium housings during adaptation! The titanium housings are then polymerized into the existing full denture and the denture also relined if necessary. After trimming and polishing the denture, the black processing replacement males are removed and replaced by corresponding replacement male as described in "Integration of the colored replacement males" on page 58. The finished prosthesis is inserted and the occlusion checked. CONVERTING AN EXISTING FULL DENTURE INTO A LOCATOR ® -RETAINED FULL DENTURE IN THE DENTAL PRACTICE Locator ® components can also be integrated in an existing full denture in the dental practice. After final insertion of the CAMLOG ® Locator ® abutments in the CAMLOG ® implants (see page 55), the white block out spacers included in the Locator ® male processing packages are pulled over the functional areas of the CAMLOG ® Locator ® abutments to prevent acrylic from getting into the titanium housings. CAUTION Undercuts between the titanium housings and the surrounding tissue not covered by the block out spacers must be blocked out. Acrylic must not get into the titanium housing during adaptation! WARNING! During intraoral use, products must be secured in general against aspiration and swallowing. The titanium housings with the black processing replacement males are positioned on each CAMLOG ® Locator ® abutment over the previously placed block out spacers until the pressure point is reached. The titanium housings are attached by the black processing replacement males and the resilience of the denture determined. The existing full denture is carefully prepared and perforated in the areas of the titanium housings. The denture must not come into contact during try-in. Contact with the housings can affect the exact positioning of the denture in the mouth. Acrylic can pass through the perforations occlusally.
The titanium housing is polymerized with suitable self-curing polymer in accordance with the manufacturer's instructions. We recommend wetting the titanium housing with acrylic. The denture is then inserted, the exact fit checked and the perforations filled with acrylic. After the acrylic has cured, the denture is removed from the mouth, acrylic overages removed and polished. The black processing replacement males are then removed and replaced by corresponding replacement males as described in "Integration of the colored replacement males" on page 58. The finished prosthesis is inserted and the occlusion checked. HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM EXCHANGE OF THE REPLACEMENT MALES IN AN EXISTING FULL DENTURE The Locator ® instrument is used to replace the replacement males if needed. The screw-on tip is turned three rotations counter-clockwise. Press the retentive tip into the replacement male and remove the male. The middle piece of the Locator ® instrument is used to integrate the colored replacement males in the empty titanium housing. The tip of the instrument is unscrewed, the replacement males positioned and pressed into the titanium housing. NOTE The titanium inserts have no friction on the middle piece. Therefore, keep the middle piece perpendicular and press in the replacement males from the basal view. See also "Integration of the colored replacement males" on page 58. 61
Page 1 and 2:
HYBRID RESTORATIONS WITH THE CAMLOG
Page 3 and 4:
LOCATOR ® ANCHORING SYSTEM PRODUCT
Page 5 and 6:
SYSTEM INTRODUCTION GENERAL GUIDELI
Page 7 and 8:
HYBRID RESTORATIONS WITH THE CAMLOG
Page 9 and 10: CAMLOG COLOR-CODING HYBRID RESTORAT
Page 11 and 12: ANCHORING OPTIONS In consideration
Page 13 and 14: CAMLOG ® CAST FABRICATION CAST FAB
Page 15 and 16: CAST FABRICATION, OPEN TRAY PREPARA
Page 17 and 18: CAMLOG ® BITE REGISTRATION POSTS I
Page 19 and 20: Remove the bite register, the bite
Page 21 and 22: BAR RESTORATIONS INTRODUCTION In im
Page 23 and 24: CAMLOG ® IMPRESSION TAKING OPTIONS
Page 25 and 26: The impression posts are then reatt
Page 27 and 28: IMPRESSION TAKING OVER THE CAMLOG
Page 29 and 30: INVESTMENT, CAST AND DEVESTMENT The
Page 31 and 32: TRIMMING After devestment and clean
Page 33 and 34: After wax-up of the bar framework,
Page 35 and 36: INSERTING THE BAR CONSTRUCTION The
Page 37 and 38: RELINING OF A BAR-SUPPORTED FULL DE
Page 39 and 40: BALL ABUTMENT ANCHORING SYSTEM INTR
Page 41 and 42: CAMLOG ® BALL ABUTMENT FOR IMPLANT
Page 43 and 44: FABRICATION OF A NEW BALL ABUTMENT-
Page 45 and 46: BONDING THE MATRICES IN THE METAL R
Page 47 and 48: BROADENING OF AN EXISTING FULL DENT
Page 49 and 50: A cold-cured polymer is used to att
Page 51 and 52: RELINING NOTE Before relining, the
Page 53 and 54: HYBRID RESTORATIONS WITH THE CAMLOG
Page 55 and 56: PROCESSING INSERTION OF THE CAMLOG
Page 57 and 58: CAST FABRICATION After taking the i
Page 59: CONVERTING AN EXISTING FULL DENTURE
Page 63 and 64: DOUBLE CROWN RESTORATIONS INTRODUCT
Page 65 and 66: CAMLOG ® UNIVERSAL ABUTMENT AND CA
Page 67 and 68: FABRICATING A TERTIARY FRAMEWORK FO
Page 69 and 70: CAMLOG ® GOLD-PLASTIC ABUTMENT The
Page 71 and 72: The investment material must be mat
Page 73 and 74: ACCESSORIES AND PROSTHETIC INSTRUME
Page 75 and 76: FURTHER DOCUMENTATION Further infor
show all

Hybrid Restorations with the CAMLOG Implant System (PDF

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?