Hybrid Restorations with the CAMLOG Implant System (PDF

More documents

Recommendations

Info

HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM BALL ABUTMENT ANCHORING SYSTEM RELINING OF A BALL ABUTMENT-RETAINED FULL DENTURE The denture-bearing area must be checked at regular intervals and if necessary adjusted by relining to ensure that the ball-retained, soft tissuesupported denture retains its long-term function. IMPRESSION TAKING The denture base is prepared in accordance with the procedures for a relining impression. For easy removal of the relining impression, the lamella retention inserts must be deactivated in the matrices with the screwdriver/ activator for ball abutment matrix before taking the impression. The lamella retention insert must not be extend out of the matrix housing (see "Setting the retention force"on page 42). The relining impression is taken over the CAMLOG ® ball abutments directly without accessories. The CAMLOG ® ball abutments must be fully overmolded and integrated with impression material. Silicone or polyether are suitable impression materials. CAST FABRICATION After the impression is taken successfully, the clinician must communicate the implant diameters used for cast fabrication to the dental laboratory. Brass ball abutment analogs of the appropriate diameter are then inserted in the matrices in the impression without stabilizing rings. The guide areas of the circular plateau ensure that the implant axis is transferred precisely to the master cast. The cast is fabricated in the usual manner with suitable material. 50
RELINING NOTE Before relining, the inner configuration of the matrices must be insulated with Vaseline to prevent acrylic from getting into the matrices. This would destroy the matrices. The prosthesis is relined in the usual dental manner. After relining, the prosthesis is trimmed and the inner configuration of the matrices cleaned. The clinician then activates the lamella retention inserts with the screwdriver/activator for ball abutment matrix (see "Setting the retention force" on page 42), the occlusion checked and the finished prosthesis inserted in its final position. FOLLOW-UP/RECALL HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM Ball abutment-retained prostheses should be checked for functional reliability initially at intervals of about three months. In doing so, harmful prosthetic movements can be detected early and eliminated by appropriate measures (replacement/activation/deactivation of matrices, relining, occlusion check). The prosthesis is cleaned and the patient instructed again under conditions of poor hygiene. NOTE Only clean the components of the ball abutments with suitable instruments. Metal instruments can damage them. REPLACING THE LAMELLA RETENTION INSERT The retention force of the lamella retention insert may be reduced by stress or wear. To replace it, use the screwdriver/activator for ball abutment matrix to unscrew it counter-clockwise from the matrix housing (see "Setting the retention force" on page 42). The new lamella retention insert is screwed in clockwise into the matrix housing. Make sure that it is placed axially. For a controlled adjustment of the retention force, the lamella retention insert is first screwed in completely and then unscrewed one complete turn. This sets the retention force to about 200 g (basic setting). The total retention force can be individually adjusted at the time of insertion of the denture. 51
Page 1 and 2: HYBRID RESTORATIONS WITH THE CAMLOG
Page 3 and 4: LOCATOR ® ANCHORING SYSTEM PRODUCT
Page 5 and 6: SYSTEM INTRODUCTION GENERAL GUIDELI
Page 9 and 10: CAMLOG COLOR-CODING HYBRID RESTORAT
Page 11 and 12: ANCHORING OPTIONS In consideration
Page 13 and 14: CAMLOG ® CAST FABRICATION CAST FAB
Page 15 and 16: CAST FABRICATION, OPEN TRAY PREPARA
Page 17 and 18: CAMLOG ® BITE REGISTRATION POSTS I
Page 19 and 20: Remove the bite register, the bite
Page 21 and 22: BAR RESTORATIONS INTRODUCTION In im
Page 23 and 24: CAMLOG ® IMPRESSION TAKING OPTIONS
Page 25 and 26: The impression posts are then reatt
Page 27 and 28: IMPRESSION TAKING OVER THE CAMLOG
Page 29 and 30: INVESTMENT, CAST AND DEVESTMENT The
Page 31 and 32: TRIMMING After devestment and clean
Page 33 and 34: After wax-up of the bar framework,
Page 35 and 36: INSERTING THE BAR CONSTRUCTION The
Page 37 and 38: RELINING OF A BAR-SUPPORTED FULL DE
Page 39 and 40: BALL ABUTMENT ANCHORING SYSTEM INTR
Page 41 and 42: CAMLOG ® BALL ABUTMENT FOR IMPLANT
Page 43 and 44: FABRICATION OF A NEW BALL ABUTMENT-
Page 45 and 46: BONDING THE MATRICES IN THE METAL R
Page 47 and 48: BROADENING OF AN EXISTING FULL DENT
Page 49: A cold-cured polymer is used to att
Page 55 and 56: PROCESSING INSERTION OF THE CAMLOG
Page 57 and 58: CAST FABRICATION After taking the i
Page 59 and 60: CONVERTING AN EXISTING FULL DENTURE
Page 61 and 62: The titanium housing is polymerized
Page 63 and 64: DOUBLE CROWN RESTORATIONS INTRODUCT
Page 65 and 66: CAMLOG ® UNIVERSAL ABUTMENT AND CA
Page 67 and 68: FABRICATING A TERTIARY FRAMEWORK FO
Page 69 and 70: CAMLOG ® GOLD-PLASTIC ABUTMENT The
Page 71 and 72: The investment material must be mat
Page 73 and 74: ACCESSORIES AND PROSTHETIC INSTRUME
Page 75 and 76: FURTHER DOCUMENTATION Further infor

Hybrid Restorations with the CAMLOG Implant System (PDF

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?