Hybrid Restorations with the CAMLOG Implant System (PDF

More documents

Recommendations

Info

HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM BALL ABUTMENT ANCHORING SYSTEM After the impression is taken successfully, the clinician must communicate the implant diameters used for cast fabrication to the dental laboratory. Brass ball abutment analogs of the appropriate diameter are then inserted in the impression without stabilizing rings. The guide areas of the circular plateau ensure that the implant axis is transferred precisely to the master cast. The cast is fabricated in the usual manner with suitable material. INTEGRATING THE MATRICES Before placing the matrices, the lamella retention inserts are insulated with vaseline. The matrices are positioned and aligned by the same procedure when fabricating a new ball abutment-retained full denture. The areas underneath are blocked out with plaster. No acrylic should get into the inner configuration of the matrices! The existing prosthesis base is hollow ground and perforated in the area of the matrices specifically. The perforation is used for visual control and to allow acrylic to escape. The matrix housings can be stained with pink opaquer as required after conditioning the surface. 48 NOTE After hollow grinding during the subsequent try-in on the cast, the prosthesis must not come into contact with the matrices and block outs! Integrating the ball abutment analogs in the impression Cast Fabrication
A cold-cured polymer is used to attach the matrix housings similar to a direct relining. The matrices must be completely wrapped with acrylic. After curing, the prosthesis is lifted with the polymerized matrices, trimmed and the inner configuration of the matrices cleaned. The clinician then activates the lamella retention inserts with the screwdriver/activator for ball abutment matrix (see "Setting the retention force" on page 42), the occlusion checked and the finished prosthesis inserted in its final position. HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM 49
Page 1 and 2: HYBRID RESTORATIONS WITH THE CAMLOG
Page 3 and 4: LOCATOR ® ANCHORING SYSTEM PRODUCT
Page 5 and 6: SYSTEM INTRODUCTION GENERAL GUIDELI
Page 9 and 10: CAMLOG COLOR-CODING HYBRID RESTORAT
Page 11 and 12: ANCHORING OPTIONS In consideration
Page 13 and 14: CAMLOG ® CAST FABRICATION CAST FAB
Page 15 and 16: CAST FABRICATION, OPEN TRAY PREPARA
Page 17 and 18: CAMLOG ® BITE REGISTRATION POSTS I
Page 19 and 20: Remove the bite register, the bite
Page 21 and 22: BAR RESTORATIONS INTRODUCTION In im
Page 23 and 24: CAMLOG ® IMPRESSION TAKING OPTIONS
Page 25 and 26: The impression posts are then reatt
Page 27 and 28: IMPRESSION TAKING OVER THE CAMLOG
Page 29 and 30: INVESTMENT, CAST AND DEVESTMENT The
Page 31 and 32: TRIMMING After devestment and clean
Page 33 and 34: After wax-up of the bar framework,
Page 35 and 36: INSERTING THE BAR CONSTRUCTION The
Page 37 and 38: RELINING OF A BAR-SUPPORTED FULL DE
Page 39 and 40: BALL ABUTMENT ANCHORING SYSTEM INTR
Page 41 and 42: CAMLOG ® BALL ABUTMENT FOR IMPLANT
Page 43 and 44: FABRICATION OF A NEW BALL ABUTMENT-
Page 45 and 46: BONDING THE MATRICES IN THE METAL R
Page 47: BROADENING OF AN EXISTING FULL DENT
Page 51 and 52: RELINING NOTE Before relining, the
Page 55 and 56: PROCESSING INSERTION OF THE CAMLOG
Page 57 and 58: CAST FABRICATION After taking the i
Page 59 and 60: CONVERTING AN EXISTING FULL DENTURE
Page 61 and 62: The titanium housing is polymerized
Page 63 and 64: DOUBLE CROWN RESTORATIONS INTRODUCT
Page 65 and 66: CAMLOG ® UNIVERSAL ABUTMENT AND CA
Page 67 and 68: FABRICATING A TERTIARY FRAMEWORK FO
Page 69 and 70: CAMLOG ® GOLD-PLASTIC ABUTMENT The
Page 71 and 72: The investment material must be mat
Page 73 and 74: ACCESSORIES AND PROSTHETIC INSTRUME
Page 75 and 76: FURTHER DOCUMENTATION Further infor

Hybrid Restorations with the CAMLOG Implant System (PDF

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?