Hybrid Restorations with the CAMLOG Implant System (PDF

More documents

Recommendations

Info

HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM SYSTEM INTRODUCTION CAMLOG ® UNIVERSAL ABUTMENT PS FOR PLATFORM SWITCHING (K-SERIES) The Platform Switching option is used to support the hard and soft tissue in esthetic regions. Due to the horizontally reduced diameter of the CAMLOG ® abutment PS in relationship to the implant diameter, the implant-abutment interface on the implant shoulder is shifted towards the middle of the implant. This makes it possible to adapt soft tissue over the implant shoulder during the prosthetic restoration. 8 PS CAMLOG ® Universal Abutment PS for Platform Switching (Ø 4.3 mm) in a CAMLOG ® SCREW-LINE implant of the K-Series. IMPORTANT NOTES • All prosthetic components for platform switching have the PS label and K article number (K-Series). • The platform switching option for double crowns is only possible with the CAMLOG ® universal abutments PS on CAMLOG ® SCREW-LINE implants (K-Series). • CAMLOG ® universal, telescope and gold-plastic abutments with J article number are not compatible with CAMLOG ® SCREW-LINE implants with the K article number (K-Series).
CAMLOG COLOR-CODING HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM To ensure that the correct lab analogs are used for the impression posts, the prosthetic components are color-coded to match the implant diameters. You should make sure to use and connect only lab analogs and prosthetic components of the same diameter (by color-coding). No components of different diameters should be joined to one another. COLOR-CODING OF THE SURGICAL AND PROSTHETICAL CAMLOG ® PRODUCTS COLOR DIAMETER gray 3.3 mm yellow 3.8 mm red 4.3 mm blue 5.0 mm green 6.0 mm 9
Page 1 and 2: HYBRID RESTORATIONS WITH THE CAMLOG
Page 3 and 4: LOCATOR ® ANCHORING SYSTEM PRODUCT
Page 5 and 6: SYSTEM INTRODUCTION GENERAL GUIDELI
Page 7: HYBRID RESTORATIONS WITH THE CAMLOG
Page 11 and 12: ANCHORING OPTIONS In consideration
Page 13 and 14: CAMLOG ® CAST FABRICATION CAST FAB
Page 15 and 16: CAST FABRICATION, OPEN TRAY PREPARA
Page 17 and 18: CAMLOG ® BITE REGISTRATION POSTS I
Page 19 and 20: Remove the bite register, the bite
Page 21 and 22: BAR RESTORATIONS INTRODUCTION In im
Page 23 and 24: CAMLOG ® IMPRESSION TAKING OPTIONS
Page 25 and 26: The impression posts are then reatt
Page 27 and 28: IMPRESSION TAKING OVER THE CAMLOG
Page 29 and 30: INVESTMENT, CAST AND DEVESTMENT The
Page 31 and 32: TRIMMING After devestment and clean
Page 33 and 34: After wax-up of the bar framework,
Page 35 and 36: INSERTING THE BAR CONSTRUCTION The
Page 37 and 38: RELINING OF A BAR-SUPPORTED FULL DE
Page 39 and 40: BALL ABUTMENT ANCHORING SYSTEM INTR
Page 41 and 42: CAMLOG ® BALL ABUTMENT FOR IMPLANT
Page 43 and 44: FABRICATION OF A NEW BALL ABUTMENT-
Page 45 and 46: BONDING THE MATRICES IN THE METAL R
Page 47 and 48: BROADENING OF AN EXISTING FULL DENT
Page 49 and 50: A cold-cured polymer is used to att
Page 51 and 52: RELINING NOTE Before relining, the
Page 53 and 54: HYBRID RESTORATIONS WITH THE CAMLOG
Page 55 and 56: PROCESSING INSERTION OF THE CAMLOG
Page 57 and 58: CAST FABRICATION After taking the i
Page 59 and 60:
CONVERTING AN EXISTING FULL DENTURE
Page 61 and 62:
The titanium housing is polymerized
Page 63 and 64:
DOUBLE CROWN RESTORATIONS INTRODUCT
Page 65 and 66:
CAMLOG ® UNIVERSAL ABUTMENT AND CA
Page 67 and 68:
FABRICATING A TERTIARY FRAMEWORK FO
Page 69 and 70:
CAMLOG ® GOLD-PLASTIC ABUTMENT The
Page 71 and 72:
The investment material must be mat
Page 73 and 74:
ACCESSORIES AND PROSTHETIC INSTRUME
Page 75 and 76:
FURTHER DOCUMENTATION Further infor
show all

Hybrid Restorations with the CAMLOG Implant System (PDF

Create successful ePaper yourself

Delete template?

Save as template?