Hybrid Restorations with the CAMLOG Implant System (PDF

More documents

Recommendations

Info

HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM BAR RESTORATIONS For impression taking, the impression post for the CAMLOG ® bar abutment is inserted into the driver for impression posts and healing caps for bar abutments. A driver is available for each implant diameter 3.3/3.8/4.3 mm and 5.0/6.0 mm. 24 Holding screw Driver Impression post Driver for impression posts and healing caps for CAMLOG ® bar abutments Mounted impression post The impression post is then screwed onto the CAMLOG ® bar abutment fitted in the CAMLOG ® implant. A closed tray is suitable for impression taking. Then use a silicone or polyether impression material to take the impression. After removing the impression, the impression posts remain on the CAMLOG ® bar abutments.
The impression posts are then reattached with the driver for impression posts and healing caps for bar abutments and unscrewed from the bar abutment. The bar abutments remain in the implants. The impression posts are handed over to the dental laboratory. The screwdriver (hex) is then used to screw healing caps for bar abutments onto the bar abutments based on the implant diameters used. The healing cap for bar abutment protects the bar abutment and at the same time assumes the function of a gingival former. CAST FABRICATION In the dental laboratory, the impression posts for bar abutments are tightened by hand to the soldering aid/bar lab analogs and repositioned in the impression. A soldering aid/bar lab analog is available for each implant diameter 3.3/3.8/4.3 mm and 5.0/6.0 mm. Impression post for bar abutment with soldering aid/bar lab analog HYBRID RESTORATIONS WITH THE CAMLOG ® IMPLANT SYSTEM 25
Page 1 and 2: HYBRID RESTORATIONS WITH THE CAMLOG
Page 3 and 4: LOCATOR ® ANCHORING SYSTEM PRODUCT
Page 5 and 6: SYSTEM INTRODUCTION GENERAL GUIDELI
Page 9 and 10: CAMLOG COLOR-CODING HYBRID RESTORAT
Page 11 and 12: ANCHORING OPTIONS In consideration
Page 13 and 14: CAMLOG ® CAST FABRICATION CAST FAB
Page 15 and 16: CAST FABRICATION, OPEN TRAY PREPARA
Page 17 and 18: CAMLOG ® BITE REGISTRATION POSTS I
Page 19 and 20: Remove the bite register, the bite
Page 21 and 22: BAR RESTORATIONS INTRODUCTION In im
Page 23: CAMLOG ® IMPRESSION TAKING OPTIONS
Page 27 and 28: IMPRESSION TAKING OVER THE CAMLOG
Page 29 and 30: INVESTMENT, CAST AND DEVESTMENT The
Page 31 and 32: TRIMMING After devestment and clean
Page 33 and 34: After wax-up of the bar framework,
Page 35 and 36: INSERTING THE BAR CONSTRUCTION The
Page 37 and 38: RELINING OF A BAR-SUPPORTED FULL DE
Page 39 and 40: BALL ABUTMENT ANCHORING SYSTEM INTR
Page 41 and 42: CAMLOG ® BALL ABUTMENT FOR IMPLANT
Page 43 and 44: FABRICATION OF A NEW BALL ABUTMENT-
Page 45 and 46: BONDING THE MATRICES IN THE METAL R
Page 47 and 48: BROADENING OF AN EXISTING FULL DENT
Page 49 and 50: A cold-cured polymer is used to att
Page 51 and 52: RELINING NOTE Before relining, the
Page 55 and 56: PROCESSING INSERTION OF THE CAMLOG
Page 57 and 58: CAST FABRICATION After taking the i
Page 59 and 60: CONVERTING AN EXISTING FULL DENTURE
Page 61 and 62: The titanium housing is polymerized
Page 63 and 64: DOUBLE CROWN RESTORATIONS INTRODUCT
Page 65 and 66: CAMLOG ® UNIVERSAL ABUTMENT AND CA
Page 67 and 68: FABRICATING A TERTIARY FRAMEWORK FO
Page 69 and 70: CAMLOG ® GOLD-PLASTIC ABUTMENT The
Page 71 and 72: The investment material must be mat
Page 73 and 74: ACCESSORIES AND PROSTHETIC INSTRUME
Page 75 and 76:
FURTHER DOCUMENTATION Further infor
show all

Hybrid Restorations with the CAMLOG Implant System (PDF

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?