Catalyst Sun Blade Computer Upgrade Manual - Zzybot.net

More documents

Recommendations

Info

Install the Ethernet Switch Assembly1) Attach the ethernet switch assembly to the side rail of the mainframe usingfour #10-32 screws (470-296-01). Orient the assembly so that the ethernetswitch faces the side cover (or expansion cabinet), and the ethernet portson the switch face the service side of the system as shown in the figureEthernet Switch Assembly Orientation.NoteAlign the 13th hole from the service side on the system chassis with the upperright threaded hole on the mounting bracket.2) Torque the screws to 30 in-lbs.Operator SideService SideEthernet Switch Assembly OrientationConnect the Ethernet Cables1) Connect the power cord left from the previous ethernet switch to thepower plug on the ethernet switch and route it to the operator side.2) Connect the user computer ethernet cable (811-113-00) to port 1 on theethernet switch.3) Connect the test computer ethernet cable (811-112-00) to port 3 on theethernet switch.4) Connect the external network cable (811-114-00) to port 8 on the ethernetswitch and route it to the strain relief bracket at the lower end of the systemcabinet, and then to the customer facility ethernet port.24 Catalyst Sun Blade Computer Upgrade Manual
Installing the Sun Blade 2500 Test Computer (Upgrading from CPU-24)Install the Outlet StripIf the system is being upgraded from an Ultra 10/60 test computer, proceed toInstalling the Sun Blade 2500 Test Computer (Upgrading from Ultra 10/60).If the system is being upgraded from a CPU-24,install the Sun Blade 2500 testcomputer, as described in the following steps. This section describes how toinstall the NETGEAR Ethernet switch.This section is composed of thefollowing subsections:• Install the Outlet Strip• Install the Power Supply Assembly• Install the Sun Blade 2500 Computer Mounting Sled• Install the Sun Blade 2500 Test Computer• Connect the Sun Blade 2500 CablesOutlet Strip and Upper Strut1) Install the outlet strip assembly from the operator side using two #10-32screws (470-296-01) at the upper most mounting hole on the modulemounting cage and nut bar location 2. See the figure Power SupplyAssembly.2) Torque the two screws to 30 in-lbs.3) Plug the outlet strip power cable into an unswitched J9 connection (A orB) of the main vault.4) Connect the Ethernet switch power cord to the outlet strip.Catalyst Sun Blade Computer Upgrade Manual 25
Page 1 and 2: Catalyst Sun Blade Computer Upgrade
Page 3 and 4: Prepare for InstallationThis topic
Page 5 and 6: Lockout Sequence1) When servicing i
Page 7 and 8: A. TagD. Connector BootB. HaspB. Ha
Page 9 and 10: Remove the Test System CoversRemovi
Page 11 and 12: 9) Disconnect cable 804-182-00 from
Page 13 and 14: Removing the Ultra 10/60 Test Compu
Page 15 and 16: 3) Remove the upper retaining brack
Page 17 and 18: On the operator side perform steps
Page 19 and 20: Transfer the PCI CardsWhen upgradin
Page 21 and 22: 5) Using a Phillips head screwdrive
Page 23: Installing the Ethernet SwitchThis
Page 27 and 28: 3) Plug the power cable (807-372-00
Page 29 and 30: 5) From the service side, mount the
Page 31 and 32: 9) Torque the nuts to 30 in-lb.10)
Page 33 and 34: Sun Blade Mounting SledSecuring Top
Page 35 and 36: 6) Insert a 1/4-20 screw through th
Page 37 and 38: Installing the Sun Blade 2500 Test
Page 39 and 40: 5) From the service side, mount the
Page 41 and 42: Install the Sun Blade 2500 Test Com
Page 43 and 44: 4) Secure the Sun Blade 2500 to the
Page 45 and 46: 6) Insert a 1/4-20 screw through th
Page 47 and 48: Connect the Sun Blade 2500 Cables1)
Page 49 and 50: Install the MonitorsMonitor #1Monit
Page 51 and 52: System VerificationOverviewAt this
Page 53 and 54: Changing a Catalyst Test System's N
Page 55 and 56: NoteIf the part is packaged in a va
Page 57 and 58: PPartsHandling Procedures 54Return

Catalyst Sun Blade Computer Upgrade Manual - Zzybot.net

Create successful ePaper yourself

Delete template?

Save as template?