Organisatorische und technische Richtlinien ... - Archiv - IAA
Organisatorische und technische Richtlinien ... - Archiv - IAA
Organisatorische und technische Richtlinien ... - Archiv - IAA
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
stützen innerhalb von Ausstellungsständen liegen,<br />
können sie durch den jeweiligen Standinhaber bis<br />
zur maximalen Bauhöhe der jeweiligen Halle verkleidet<br />
werden. Versorgungseinrichtungen müssen<br />
zugänglich bleiben. In einer Höhe von mehr als<br />
3,50 m über dem Hallenboden darf diese Verkleidung<br />
in jeder Richtung höchstens 20 cm über die<br />
Kontur der Hallenstütze hinausragen.<br />
4.2.1.6 Standbegrenzungswände<br />
Standbegrenzungswände sind messeseitig nicht<br />
vorhanden. Trenn- <strong>und</strong> Kabinenwände können bei<br />
der Deutschen Messe AG über die Servicemappe<br />
bestellt werden.<br />
4.2.1.7 Werbeaufbauten<br />
(Aufbauten über 3,50 – 6,50 m Höhe)<br />
Werbeaufbauten sind nur in den unter Abschnitt<br />
4.2.3.1 gekennzeichneten Hallen zulässig.<br />
Werbeaufbauten bis zu einer Höhe von 6,50 m ab<br />
Oberkante Hallenboden sind bei Einhaltung folgender<br />
Punkte zulässig:<br />
– Die Standfläche muss größer als 300 m2 sein.<br />
– Gr<strong>und</strong>fläche der Aufbauten darf 10 % der Standfläche<br />
nicht überschreiten.<br />
– Abstand zu allen Standgrenzen mind. 3,00 m.<br />
– Beachtung der maximalen Nutzhöhe über der<br />
gemieteten Standfläche.<br />
– Drehbare Aufbauten maximal 2 Umdrehungen/<br />
Minute.<br />
– Auf Fahrzeugständen, deren Exponate höher als<br />
3,50 m sind.<br />
4.2.1.8 Schriften <strong>und</strong> Zeichen<br />
Oberhalb der in Abschnitt 4.2.1.9 festgelegten Höhe<br />
dürfen nur Markennamen <strong>und</strong> Firmenzeichen des<br />
Herstellers der ausgestellten Kraftfahrzeuge sowie<br />
die zur Abstützung <strong>und</strong> Befestigung notwendigen<br />
Bauelemente angeracht werden. Die Gesamtzahl A<br />
der Markennamen <strong>und</strong> Firmenzeichen darf den aus<br />
der nachstehenden Gleichung errechneten Wert<br />
nicht überschreiten:<br />
22<br />
Standfläche (m2 )<br />
A = 3 +<br />
500<br />
(aufger<strong>und</strong>et). Doppelseitig wirkende Schriften <strong>und</strong><br />
Zeichen werden als zwei Systeme gezählt.<br />
Die Oberkante der Markennamen bzw. der Schriftbänder<br />
mit den Markennamen darf eine Höhe von<br />
6,50 m über dem Hallenboden nicht überschreiten.<br />
Die Buchstaben bzw. die Schriftbänder dürfen nicht<br />
höher sein als 80 cm. Offene Neonröhren, Blinkschriften<br />
oder andere Lichteffekte sind nicht zulässig.<br />
Firmenzeichen müssen sich mit einem Rechteck<br />
von 2,5 m2 Fläche umschreiben lassen. Ihr höchster<br />
Punkt darf nicht weiter als 6,50 m vom Hallboden<br />
entfernt sein.<br />
column within the confines of an exhibition stand up<br />
to the max. construction heigth. Supply installations<br />
must remain accessible. At a heigth of more than<br />
3.50 m above the hall floor, the covering may protrude<br />
up to a maximum of 20 cm in all directions<br />
beyond the surface of the column.<br />
4.2.1.6 Stand partitions<br />
Partitions at stand bo<strong>und</strong>aries are not provided. Simple<br />
separating partitions and cubicle partitions can<br />
be ordered from the manual “Services offered”.<br />
4.2.1.7 Advertising fixtures (structures<br />
exceeding a height of 3.50 – 6.50 m)<br />
Advertising fixtures are permissible only in the hall<br />
indicated in par. 4.2.3.1.<br />
Advertising fixtures of a maximum height of 6.50 m<br />
above the floor surface are permissible that the following<br />
requirements are met:<br />
– The stand area must exceed 300 m2 .<br />
– The floor area covered by the fixtures must not<br />
exceed 10 % of the total stand area.<br />
– Minimum distance from all stand bo<strong>und</strong>aries:<br />
3.00 m.<br />
– Conformity with max. usable height above the<br />
rented stand surface.<br />
– Revolving fixtures must not revolve at more than<br />
2 rpm.<br />
– On vehicle stands which have exhibits higher than<br />
3.50 m.<br />
4.2.1.8 Lettering and signs<br />
Only brand names and company logos of the manufacturer<br />
of the exhibited motor vehicles as well as<br />
the supports and mountings may be attached at a<br />
height exceeding the height specified in par. 4.2.1.9.<br />
The total quantity A of brand names and company<br />
signs must not exceed the value calculated below,<br />
using the following equation:<br />
Stand area (m2 )<br />
A = 3 +<br />
500<br />
(ro<strong>und</strong>ed up). Double-sided lettering and signs are<br />
considered to be two systems.<br />
The top edge of the brand names or the panels bearing<br />
the brand names must not be more than 6.50 m<br />
above the hall floor. The characters or the panels<br />
must not be greater than 80 cm in height. Open neon<br />
tubes, flashing lettering or other light effects are not<br />
permitted.<br />
Company signs must have a size that can be covered<br />
by a rectangular surface area of 2.5 m2 . The<br />
highest point must not be more than 6.50 m away<br />
from the hall floor.