CLV63x Bar Code Scanner CLV63x Bar Code Scanner - Sick

More documents

Recommendations

Info

Startup and configuration Chapter 7 Operating Instructions 7.5 Default setting CLV63x Bar Code Scanner The values of the default setting are permanently saved in the bar code scanner (ROM) and in the database of the SOPAS-ET configuration software in the device-specific jar file (see chapter 7.4 First startup, page 66). A PC is not required to start up the bar code scanner with the default setting. 7.5.1 Resetting the default setting in the bar code scanner Prerequisite The SOPAS-ET configuration software is connected online to the bar code scanner. Two default setting types can be called up via the SOPAS-ET configuration software: • Complete default setting (LOAD FACTORY DEFAULT) SOPAS-ET resets all parameter values of the bar code scanner to default. Settings which have been previously made for the communication parameters of the Ethernet interfaces or serial data interfaces (e.g. Ethernet address) are overwritten. The connection(s) to the bar code scanner might be interrupted and has (have) to be reconfigured. • Application-specific default setting (LOAD APPLICATION DEFAULT) SOPAS-ET resets the parameter values of the bar code scanner but does not change the communication parameters. Settings which have been previously made for the communication parameters of the Ethernet interfaces or serial data interfaces are kept and the current connection(s) to the bar code scanner remain(s) established. 1. In order to discard changes to the parameter set as described above, select the corresponding command in the menu bar under CLV63X. The SOPAS-ET configuration software loads the default setting from the bar code scanner and displays the parameter values in the register tabs. In the bar code scanner, the default setting will first be active in the temporary main memory only. The default setting can also be saved on or printed via the PC, chapter 7.4.4 Save, display and print the current parameter set, page 67. 2. In the menu bar under TOOLS select the command LOGIN DEVICE. 3. In the dialog window under USERLEVEL in the list box select the entry AUTORIZED CLIENT. If the parameter set is password-protected, enter the password "client" in PASSWORD. 4. Click on OK to confirm the dialog window. 5. In the menu bar under CLV63X select the command PARAMETER/SAVE PERMANENT. The SOPAS-ET configuration software transfers the default setting to the permanent parameter memory (PROM) of the bar code scanner. If the bar code scanner is equiped with the Micro SD memory card or connected to a connection module CDB620/CDM420 with parameter memory module CMC600, the default setting will be permanently transferred to parameter memory CMC600 or memory card respectively. Important Once the default setting has been restored, password-protection is deactivated. 68 © SICK AG · Division Auto Ident · Germany · All rights reserved 8011970/S345/2008-04-16
Operating Instructions Chapter 7 CLV63x Bar Code Scanner Startup and configuration 7.6 Adjusting the bar code scanner 7.6.1 Adjusting the bar code scanner To completely adjust the bar code scanner, the electrical installation must be complete and the device must be operated, see chapter 6 Electrical installation, page 49 and chapter 7 Startup and configuration, page 63. 1. Align the bar code scanner in such a way that the angle between the scanning line and the bar code's lines is almost 90°. 2. To avoid disruptive reflections, rotate the bar code scanner from the plumb line so that the emitting light meets the bar code at an angle of approx. 105° (line scanner), chapter 5.3.4 Avoiding surface reflections, page 44. 3. Manually bring objects with bar codes sequentially into the bar code scanner's visual range. The default setting of the focal position is 285 mm (11.2 in) from the reading window. Check the reading result using the SOPAS-ET configuration software. Move objects in different positions (angles) to the reading area and ensure that the thresholds of the permitted reading angles are not exceeded. 4. Align the bar code scanner in such a way that the good read rate is between 70 and 100%. 5. Tighten the screws on the bar code scanner. The bar code scanner is aligned with the bar code. 8011970/S345/2008-04-16 © SICK AG · Division Auto Ident · Germany · All rights reserved 69
Page 1 and 2:
CLV63x Bar Code Scanner CLV63x Bar
Page 3 and 4:
Operating Instructions CLV63x Bar C
Page 5 and 6:
Operating Instructions Chapter CLV6
Page 7 and 8:
Operating Instructions Chapter CLV6
Page 9 and 10:
Operating Instructions Chapter 1 CL
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18: Operating Instructions Chapter 3 CL
Page 67: Operating Instructions Chapter 7 CL
Page 77 and 78: Operating Instructions Chapter 10 C
Page 119 and 120:
Operating Instructions Chapter 11 C
show all

CLV63x Bar Code Scanner CLV63x Bar Code Scanner - Sick

Create successful ePaper yourself

Delete template?

Save as template?