Apple Technician Guide MacBook Pro (17-inch, Early 2009) - tim.id.au

More documents

Recommendations

Info

First Steps Remove: • Bottom case • Battery • Memory • Fans • Logic board Trackpad Kit 922-9009 includes: • trackpad • black label • 10 bottom case screws (3-mm and 13.5-mm) • 6 Phillips #000 (2-mm) screws • 1 tri-lobe #0 set screw • 2 metal flexures Tools • ESD wrist strap and mat • Sticky (Post-It) notes • Black stick • Large tri-lobe #0 screwdriver (922-8991) • Magnetized Phillips #00 screwdriver • Magnetized Phillips #000 screwdriver • Magnetized Torx T6 screwdriver 2010-06-11 Trackpad MacBook Pro (17-inch, Early 2009) Take Apart — Trackpad 188
Removal 1 Remove 6 #000 (2-mm) Phillips screws from flexures. Discard old screws; they lose their ability to hold securely if reused. 2 Remove 4 T6 (4-mm) screws from flexure stiffeners. Keep screws. 3 Remove 1 tri-lobe set screw. Discard old screw. 4 Slide out stiffeners and flexures. Keep stiffeners. 5 Dispose of flexures (thin metal pieces); they are matched to each individual trackpad by thickness. 2010-06-11 MacBook Pro (17-inch, Early 2009) Take Apart — Trackpad 189
Page 1 and 2:
apple Apple Technician Guide MacBoo
Page 3 and 4:
MacBook Pro (17-inch, Early 2009) C
Page 5 and 6:
Specific Keys Don’t Work 95 Built
Page 7 and 8:
Replacement 203 Left Speaker 205 Mi
Page 9 and 10:
2010-06-11 Take Apart: • Connecto
Page 11 and 12:
apple Apple Technician Guide Basic
Page 13 and 14:
2010-06-11 • Product identificati
Page 15 and 16:
2010-06-11 Serial Number Location S
Page 17 and 18:
2010-06-11 General Information Requ
Page 19 and 20:
apple Apple Technician Guide Troubl
Page 21 and 22:
2010-06-11 Troubleshooting Theory F
Page 23 and 24:
2010-06-11 1920x1200 LCD Display Di
Page 25 and 26:
2010-06-11 Liquid Submersion Indica
Page 27 and 28:
2010-06-11 Resetting the Parameter
Page 29 and 30:
2010-06-11 Display Hinge Behavior T
Page 31 and 32:
2010-06-11 Deep Dive Check Result A
Page 33 and 34:
2010-06-11 Won’t Start Up Unlikel
Page 35 and 36:
2010-06-11 8. Use Disk Utility load
Page 37 and 38:
2010-06-11 Suggested steps for trou
Page 39 and 40:
2010-06-11 5. Check system running
Page 41 and 42:
Page 43 and 44:
2010-06-11 9. Check for No Backligh
Page 45 and 46:
2010-06-11 4. Does battery status i
Page 47 and 48:
2010-06-11 Kernel Panic/System Cras
Page 49 and 50:
2010-06-11 6. Disconnect display as
Page 51 and 52:
2010-06-11 Power Adapter Issue Unli
Page 53 and 54:
2010-06-11 3. Disconnect any periph
Page 55 and 56:
2010-06-11 3. Is the computer opera
Page 57 and 58:
2010-06-11 2. Isolate OS by booting
Page 59 and 60:
2010-06-11 2. Run Clamshell Service
Page 61 and 62:
2010-06-11 3. Verify the antenna co
Page 63 and 64:
2010-06-11 8. Continue to test a kn
Page 65 and 66:
2010-06-11 Wireless Performance Iss
Page 67 and 68:
2010-06-11 Wireless Input Device Do
Page 69 and 70:
2010-06-11 Display Display Anomalie
Page 71 and 72:
2010-06-11 7. Substitute a known-go
Page 73 and 74:
2010-06-11 Deep Dive: Non-uniform B
Page 75 and 76:
2010-06-11 Blank / No Video Unlikel
Page 77 and 78:
2010-06-11 4. Swap memory with know
Page 79 and 80:
2010-06-11 Cosmetic Defects Quick C
Page 81 and 82:
2010-06-11 4. After reseating hard
Page 83 and 84:
2010-06-11 Hard Drive Noisy Unlikel
Page 85 and 86:
Page 87 and 88:
2010-06-11 2. Can optical drive rea
Page 89 and 90:
2010-06-11 Optical Drive Noisy Unli
Page 91 and 92:
2010-06-11 Optical Drive Not Perfor
Page 93 and 94:
2010-06-11 Input/Output Devices USB
Page 95 and 96:
2010-06-11 3. Disconnect and verify
Page 97 and 98:
2010-06-11 6. Does the select butto
Page 99 and 100:
Page 101 and 102:
2010-06-11 6. Does a known-good tra
Page 103 and 104:
Page 105 and 106:
2010-06-11 Express Card Will Not In
Page 107 and 108:
2010-06-11 FireWire Port Not Recogn
Page 109 and 110:
2010-06-11 2. Remove battery and AC
Page 111 and 112:
2010-06-11 8. Inspect and reseat co
Page 113 and 114:
Vertical Insertion (JST) • Use bl
Page 115 and 116:
Replacement Caution: When connectin
Page 117 and 118:
First Steps Warning: • Shut down
Page 119 and 120:
2 Remove 10 screws: • 3 (13.5 mm)
Page 121 and 122:
2 Install bottom case so that 4 cli
Page 123 and 124:
Removal Important: Battery removal
Page 125 and 126:
Replacement 1 Slide front edge of b
Page 127 and 128:
First Steps Remove: • Bottom case
Page 129 and 130:
First Steps Remove: • Bottom case
Page 131 and 132:
3 Hold hard drive by the sides only
Page 133 and 134:
2010-06-11 Reinstalling Software th
Page 135 and 136:
Tools • Clean, soft, lint-free cl
Page 137 and 138: 2 Press card down. 3 If you install
Page 139 and 140: Tools Clean, soft, lint-free cloth
Page 141 and 142: Replacement 1 Remove any adhesive r
Page 147 and 148: First Steps Remove: • Bottom case
Page 151 and 152: Replacement Caution: When connectin
Page 159 and 160: 5 Flip over board. 6 Lift lever to
Page 161 and 162: Tools • Clean, soft, lint-free cl
Page 165 and 166: 7 Open the display to 90 degrees, a
Page 167 and 168: 4 With computer closed and flat on
Page 171 and 172: 4 Tilt up end of clutch cover as yo
Page 173 and 174: Refer to AirPort Card 2010-06-11 Ca
Page 175 and 176: Removal 1 Cover display with clean,
Page 177 and 178: 3 Place the cable in the clip befor
Page 185 and 186: 3 Refer to Connector Types to caref
Page 187: Replacement If replacing the logic
Page 191 and 192: 9 Tilt up top case, and spiral trac
Page 193 and 194: 3 Slide stiffeners over the flexure
Page 195 and 196: 9 Fold sticky notes over so that to
Page 199 and 200: Replacement Caution: Plug in a disc
Page 203 and 204: 4 With a black stick, scrape off th
Page 207 and 208: 2 Remove 2 (8.1-mm) 922-8720 screws
Page 209 and 210: Removal Note: Do not touch the soft
Page 215 and 216: apple Apple Technician Guide Views
Page 217 and 218: 2010-06-11 Main Assembly, 2 of 2: M
Page 219 and 220: 2010-06-11 Bottom Case 922-9024 Blu
Page 221 and 222: 2010-06-11 External Views Front Vie
Page 223 and 224: 2010-06-11 Screw Location Diagrams
Page 225 and 226: 2010-06-11 Display Assembly All scr
show all

Apple Technician Guide MacBook Pro (17-inch, Early 2009) - tim.id.au

Create successful ePaper yourself

Delete template?

Save as template?