Owner's Manual - Roland

More documents

Recommendations

Info

Creating a Patch Patch Mtrx Control 1–4 Source (Patch Matrix Control 1–4) Control 1–4 Source (Matrix Control Source 1–4) 122 Sets the MIDI message used to change the tone parameter with the Matrix Control. Value OFF: Matrix control will not be used. CC01–31, 33–95: Controller numbers 1–31, 33–95 PITCH BEND: Pitch Bend AFTERTOUCH: Aftertouch SYS CTRL1–SYS CTRL4: MIDI messages used as common matrix controls. VELOCITY: Velocity (pressure you press a key with) KEYFOLLOW: Keyfollow (keyboard position with C4 as 0) TEMPO: The tempo of an external MIDI sequencer. LFO1: LFO 1 LFO2: LFO 2 PITCH ENV: Pitch envelope TVF ENV: TVF envelope TVA ENV: TVA envelope Velocity and Keyfollow correspond to Note messages. Although there are no MIDI messages for LFO 1 through TVA Envelope, they can be used as Matrix Control. In this case, you can change the tone settings in realtime by playing patches. • If you want to use common controllers for the entire Fantom VS, select “SYS CTRL1”–”SYS CTRL4.” MIDI messages used as System Control 1–4 are set with the System Ctrl 1–4 Source parameters (p. 152). There are parameters that determine whether or not Pitch Bend, Controller Number 11 (Expression) and Controller Number 64 (Hold 1) are received (p. 120). When these settings are “ON,” and the MIDI messages are received, then when any change is made in the settings of the desired parameter, the Pitch Bend, Expression, and Hold 1 settings also change simultaneously. If you want to change the targeted parameters only, then set these to “OFF.” • There are parameters that let you specify whether specific MIDI messages will be received for each channel in a performance (p. 141). When a patch with Matrix Control settings is assigned to a part, confirm that any MIDI messages used for the Matrix Control will be received. If the Fantom VS is set up such that reception of MIDI messages is disabled, then the Matrix Control will not function. CTRL Destination 1–4 (Matrix Control Destination 1–4) Matrix Control Destination selects the tone parameter that is to be controlled when using the Matrix Control. The following parameters can be controlled. When not controlling parameters with the Matrix Control, set this to “OFF.” Up to four parameters can be specified for each Matrix Control, and controlled simultaneously. In this manual, Parameters that can be controlled using the Matrix Control are marked with a “★.”
● Opening and Closing the Filter CUTOFF: Changes the cutoff frequency. RESONANCE: Emphasizes the overtones in the region of the cutoff frequency, adding character to the sound. ● Changing the Volume, Pan, and Pitch LEVEL: Changes the volume level. PAN: Changes the pan. PITCH: Changes the pitch. ● Changing How the Effects Are Applied OUTPUT LEVEL: Changes the volume of output levels. CHORUS SEND: Changes the amount of chorus. REVERB SEND: Changes the amount of reverb. ● Applying LFO to Modulate Sounds LFO1/LFO2 PCH DEPTH: Changes the vibrato depth. LFO1/LFO2 TVF DEPTH: Changes the wah depth. LFO1/LFO2 TVA DEPTH: Changes the tremolo depth. LFO1/LFO2 PAN DEPTH: Changes the effect that the LFO will have on pan. LFO1/LFO2 RATE: Changes the LFO cycle rate. Changes the speed of the LFO cycles. The speed will not change if LFO Rate is set to “note.” ● Changing the Pitch Envelope PIT ENV A-TIME: Changes the Env Time 1 parameter of the pitch envelope. PIT ENV D-TIME: Changes the Env Time 2 and Env Time 3 parameters of the pitch envelope. PIT ENV R-TIME: Changes the Env Time 4 parameter of the pitch envelope. ● Changing the TVF Envelope Creating a Patch TVF ENV A-TIME: Changes the Env Time 1 parameter of the TVF envelope. TVF ENV D-TIME: Changes the Env Time 2 and Env Time 3 parameters of the TVF envelope. TVF ENV R-TIME: Changes the Env Time 4 parameter of the TVF envelope. ● Changing the TVF Envelope TVA ENV A-TIME: Changes the Env Time 1 parameter of the TVA envelope. TVA ENV D-TIME: Changes the Env Time 2 and Env Time 3 parameters of the TVA envelope. TVA ENV R-TIME: Changes the Env Time 4 parameter of the TVA envelope. ● Splitting Tones That Are Played TMT If the Matrix Control is used to split tones, set the TMT Vel Control parameter to “OFF,” and the TMT Control Switch parameter to “ON” (p. 104, p. 105). • If the Matrix Control is used to split tones, we recommend setting the Matrix Control Sens to “+63.” Selecting a lower value may prevent switching of the tones. Furthermore, if you want to reverse the effect, set the value to “-63.” • If you want to use matrix control to switch smoothly between tones, use the Velo Fade Lower and Velo Fade Upper parameters (p. 104). The higher the values set, the smoother the switch is between the tones. 123 Overview Connections VS-700C Console VS-700R I/O Fantom VS Appendix
Page 2 and 3:
WARNING: To reduce the risk of fire
Page 4 and 5:
USING THE UNIT SAFELY 013 • In ho
Page 6 and 7:
6 IMPORTANT NOTES Power Supply 301
Page 8 and 9:
8 Contents USING THE UNIT SAFELY...
Page 10 and 11:
Contents 10 VS-700R I/O ...........
Page 12 and 13:
Contents 12 Appendix ..............
Page 14 and 15:
fig.panel-vs-700.eps 14 Main Featur
Page 16 and 17:
Panel Descriptions C. Time Display
Page 18 and 19:
Panel Descriptions Rear Panel fig.p
Page 20 and 21:
Panel Descriptions E. SAMPLE RATE K
Page 22 and 23:
Panel Descriptions E. DIGITAL 2 OUT
Page 24 and 25:
Panel Descriptions Side Panel fig.p
Page 26 and 27:
26 Connections Connecting the Power
Page 28 and 29:
941 945 28 Turning the Power On Onc
Page 30 and 31:
30 Overview of the VS-700C Console
Page 32 and 33:
CHANNEL STRIP Section Channel Fader
Page 34 and 35:
CHANNEL STRIP Section Rotary Encode
Page 36 and 37:
CHANNEL STRIP Section Strip Select
Page 38 and 39:
CHANNEL STRIP Section ASSIGN Button
Page 40 and 41:
CHANNEL STRIP Section Rude MUTE/Rud
Page 42 and 43:
CHANNEL STRIP Section FADER BANK Bu
Page 44 and 45:
CHANNEL STRIP Section I/O Control 4
Page 46 and 47:
CHANNEL STRIP Section Locking a Cha
Page 48 and 49:
fig.22.eps 48 Time Display The VS-7
Page 50 and 51:
CHANNEL STRIP CONTROL Section (EQ,
Page 52 and 53:
CHANNEL STRIP CONTROL Section (EQ,
Page 54 and 55:
fig.28.eps 54 Transport Section The
Page 56 and 57:
fig.29.eps 56 PROJECT Section The P
Page 58 and 59:
JOG/SHUTTLE/CURSOR Section Transpor
Page 60 and 61:
JOG/SHUTTLE/CURSOR Section Zoom Mod
Page 62 and 63:
JOG/SHUTTLE/CURSOR Section Edit Mod
Page 64 and 65:
fig.31.eps 64 ACCESS PANEL Section
Page 66 and 67:
ACCESS PANEL Section (Assignable Bu
Page 68 and 69:
fig.34.eps 68 SURROUND Section The
Page 70 and 71:
fig.37.eps 70 AUDIO OUTPUT Section
Page 72 and 73: RECORD/EDIT Section To Specify the
Page 74 and 75: 74 Controlling Plug-ins from the VS
Page 76 and 77: Controlling Plug-ins from the VS-70
Page 78 and 79: 78 Connecting Recording Equipment C
Page 80 and 81: 80 Switching the Sampling Rate Use
Page 82 and 83: 82 Audio Clock Source You can choos
Page 84 and 85: 84 Preamp Parameters Preamps are bu
Page 86 and 87: 86 Direct Monitor Mixer Input Setti
Page 88 and 89: 88 Inserting the Fantom VS Plug-In
Page 90 and 91: 90 Fantom VS Editor (Editing a Soun
Page 92 and 93: Overview of the Fantom VS Patches f
Page 94 and 95: Overview of the Fantom VS Note Prio
Page 96 and 97: 96 Creating a Patch With the Fantom
Page 98 and 99: Creating a Patch Stretch Tune Depth
Page 100 and 101: Creating a Patch Portamento Switch
Page 102 and 103: Creating a Patch fig.06-020 fig.06-
Page 104 and 105: Creating a Patch Key Fade Upper (Ke
Page 106 and 107: Creating a Patch FXM Color 106 Spec
Page 108 and 109: Creating a Patch Pitch Keyfollow fi
Page 110 and 111: Creating a Patch Cutoff Frequency
Page 112 and 113: Creating a Patch F-Env T4 V-Sens (T
Page 114 and 115: Creating a Patch Bias Direction 114
Page 116 and 117: Creating a Patch Output Settings Pa
Page 118 and 119: Creating a Patch Delay Time (LFO1/L
Page 120 and 121: Creating a Patch ● Apply the LFO
Page 124 and 125: Creating a Patch ● Changing the D
Page 126 and 127: Creating a Rhythm Set Tone Pitch Be
Page 128 and 129: Creating a Rhythm Set Wave Level 12
Page 130 and 131: Creating a Rhythm Set Rhythm Pitch
Page 132 and 133: Creating a Rhythm Set Cutoff V-Curv
Page 134 and 135: Creating a Rhythm Set Random Pan De
Page 136 and 137: 136 Creating a Performance With the
Page 138 and 139: Creating a Performance Reverb Send
Page 140 and 141: Creating a Performance Key Fade Low
Page 142 and 143: Creating a Performance Equal Temper
Page 144 and 145: 144 Adding Effects This section exp
Page 146 and 147: Adding Effects Functions of Effect
Page 148 and 149: Adding Effects Reverb Output 14 Rev
Page 150 and 151: Adding Effects Chorus Source 150 Se
Page 152 and 153: System Settings 152 System Control
Page 154 and 155: fig.VS-700R-block.eps 154 VS-700R B
Page 156 and 157: Installing the ARX Expansion Board
Page 158 and 159: Installing the ARX Expansion Board
Page 160 and 161: Installation de la carte d’expans
Page 162 and 163: Installation de la carte d’expans
Page 164 and 165: 164 Using only the VS-700C Console
Page 166 and 167: 166 Connecting Two VS-700R I/O Unit
Page 168 and 169: fig.38.eps 168 Connecting an EDIROL
Page 170 and 171: About V-LINK Settings for SONAR 170
Page 172 and 173:
172 Specifications VS-700C, VS-700R
Page 174 and 175:
Specifications 962a 174 Dimensions
Page 176 and 177:
Index flag ........................
Page 178 and 179:
Index WORDCLOCK OUT Connector .....
Page 180 and 181:
Index (Fantom VS) Patch ...........
Page 182 and 183:
Index (Fantom VS) Receive Program C
Page 184 and 185:
MEMO 184
Page 186 and 187:
186 For EU Countries UK DE FR IT ES
Page 188:
* 5 1 0 0 0 0 2 2 4 6 - 0 1 *
show all

Owner's Manual - Roland

Create successful ePaper yourself

Delete template?

Save as template?