Owner's Manual - Roland

More documents

Recommendations

Info

Creating a Performance Reverb Send Level (Part Reverb Send Level) 138 Sets the level of the signal sent to reverb for each part. Value: 0–127 Cutoff Offset Adjusts the cutoff frequency for the patch or rhythm set assigned to a part. Value: -64– +63 Patches also have a Cutoff Offset setting (p. 98). The final Cutoff frequency value is the sum of the tone Cutoff Frequency value and the patch and part Cutoff Offset values. If the tone’s cutoff frequency is already set to “127” (maximum), there will be no change produced by setting the Cutoff Offset to a positive value. Resonance Offset Adjusts the Resonance for the patch or rhythm set assigned to a part. Value: -64– +63 Patches also have a Resonance Offset setting (p. 98). The final Resonance value is the sum of the tone Resonance value and the patch and part Resonance Offset values. If the tone’s resonance is already set to “127” (maximum), there will be no change produced by setting the resonance offset to a positive value. Attack Time Offset Adjusts the TVA/TVF Envelope Attack Time for the patch or rhythm set assigned to a part. Value: -64– +63 Patches also contain the Attack Time Offset setting (p. 98). The final TVA Envelope attack time value is therefore the sum of the tone’s TVA Envelope Time 1 setting, the patch’s Attack Time Offset, and the part’s Attack Time Offset. If the tone’s Time 1 parameter is already set to “127” (maximum), there will be no change produced by setting the Attack Time Offset to a positive value.The same applies to the TVF envelope. Release Time Offset Adjusts the TVA/TVF Envelope Release Time for the patch or rhythm set assigned to a part. Value: -64– +63 Patches also contain a Release Time Offset setting (p. 99). The final TVA Envelope release time value is therefore the sum of the tone’s TVA Envelope Time 4 setting, the patch’s Release Time Offset, and the part’s Release Time Offset. If the tone’s Time 4 parameter is set to “127” (maximum), there will be no change in the Release Time Offset, even when this is set to a positive value.The same applies to the TVF envelope. Decay Time Offset Adjusts the TVA/TVF Envelope Decay Time for the patch or rhythm set assigned to a part. Value: -64– +63
Mono/Poly Set this parameter to “MONO” when the patch assigned to the part is to be played monophonically, or to “POLY” when the patch is to be played polyphonically. If you want to use the Mono/Poly setting of the patch assigned to the part (p. 99), set this to “PAT.” Value: MONO, POLY, PAT Legato Switch This setting is ignored for parts to which a rhythm set is assigned. You can add legato when performing monophonically. The term “legato” refers to a playing style in which notes are smoothly connected to create a flowing feel. This creates a smooth transition between notes, which is effective when you wish to simulate the hammering-on and pulling-off techniques used by a guitarist. Turn this parameter “ON” when you want to use the Legato feature and “OFF” when you don’t. If you want to use the Legato Switch setting of the patch assigned to the part (p. 99), set this to “PAT.” Value: OFF, ON, PAT This setting is ignored for parts to which a rhythm set is assigned. Portamento Switch Specify whether portamento will be applied. Turn this parameter “ON” when you want to apply Portamento and “OFF” when you don’t. If you want to use the Portamento Switch setting of the patch assigned to the part (p. 100), set this to “PAT.” Value: OFF, ON, PAT This setting is ignored for parts to which a rhythm set is assigned. Portamento Time Creating a Performance When portamento is used, this specifies the time over which the pitch will change. Higher settings will cause the pitch change to the next note to take more time. If you want to use the Portamento Time setting of the patch assigned to the part (p. 100), set this to “PAT.” Value: 0–127, PAT Vibrato Rate This setting is ignored for parts to which a rhythm set is assigned. For each part, adjust the vibrato speed (the rate at which the pitch is modulated). The pitch will be modulated more rapidly for higher settings, and more slowly with lower settings. Value: -64– +63 Vibrato Depth For each part, this adjusts the depth of the vibrato effect (the depth at which the pitch is modulated). The pitch will be modulated more greatly for higher settings, and less with lower settings. Value: -64– +63 Vibrato Delay For each part, this adjusts the time delay until the vibrato (pitch modulation) effect begins. Higher settings will produce a longer delay time before vibrato begins, while lower settings produce a shorter time. Value: -64– +63 139 Overview Connections VS-700C Console VS-700R I/O Fantom VS Appendix
Page 2 and 3:
WARNING: To reduce the risk of fire
Page 4 and 5:
USING THE UNIT SAFELY 013 • In ho
Page 6 and 7:
6 IMPORTANT NOTES Power Supply 301
Page 8 and 9:
8 Contents USING THE UNIT SAFELY...
Page 10 and 11:
Contents 10 VS-700R I/O ...........
Page 12 and 13:
Contents 12 Appendix ..............
Page 14 and 15:
fig.panel-vs-700.eps 14 Main Featur
Page 16 and 17:
Panel Descriptions C. Time Display
Page 18 and 19:
Panel Descriptions Rear Panel fig.p
Page 20 and 21:
Panel Descriptions E. SAMPLE RATE K
Page 22 and 23:
Panel Descriptions E. DIGITAL 2 OUT
Page 24 and 25:
Panel Descriptions Side Panel fig.p
Page 26 and 27:
26 Connections Connecting the Power
Page 28 and 29:
941 945 28 Turning the Power On Onc
Page 30 and 31:
30 Overview of the VS-700C Console
Page 32 and 33:
CHANNEL STRIP Section Channel Fader
Page 34 and 35:
CHANNEL STRIP Section Rotary Encode
Page 36 and 37:
CHANNEL STRIP Section Strip Select
Page 38 and 39:
CHANNEL STRIP Section ASSIGN Button
Page 40 and 41:
CHANNEL STRIP Section Rude MUTE/Rud
Page 42 and 43:
CHANNEL STRIP Section FADER BANK Bu
Page 44 and 45:
CHANNEL STRIP Section I/O Control 4
Page 46 and 47:
CHANNEL STRIP Section Locking a Cha
Page 48 and 49:
fig.22.eps 48 Time Display The VS-7
Page 50 and 51:
CHANNEL STRIP CONTROL Section (EQ,
Page 52 and 53:
CHANNEL STRIP CONTROL Section (EQ,
Page 54 and 55:
fig.28.eps 54 Transport Section The
Page 56 and 57:
fig.29.eps 56 PROJECT Section The P
Page 58 and 59:
JOG/SHUTTLE/CURSOR Section Transpor
Page 60 and 61:
JOG/SHUTTLE/CURSOR Section Zoom Mod
Page 62 and 63:
JOG/SHUTTLE/CURSOR Section Edit Mod
Page 64 and 65:
fig.31.eps 64 ACCESS PANEL Section
Page 66 and 67:
ACCESS PANEL Section (Assignable Bu
Page 68 and 69:
fig.34.eps 68 SURROUND Section The
Page 70 and 71:
fig.37.eps 70 AUDIO OUTPUT Section
Page 72 and 73:
RECORD/EDIT Section To Specify the
Page 74 and 75:
74 Controlling Plug-ins from the VS
Page 76 and 77:
Controlling Plug-ins from the VS-70
Page 78 and 79:
78 Connecting Recording Equipment C
Page 80 and 81:
80 Switching the Sampling Rate Use
Page 82 and 83:
82 Audio Clock Source You can choos
Page 84 and 85:
84 Preamp Parameters Preamps are bu
Page 86 and 87:
86 Direct Monitor Mixer Input Setti
Page 88 and 89: 88 Inserting the Fantom VS Plug-In
Page 90 and 91: 90 Fantom VS Editor (Editing a Soun
Page 92 and 93: Overview of the Fantom VS Patches f
Page 94 and 95: Overview of the Fantom VS Note Prio
Page 96 and 97: 96 Creating a Patch With the Fantom
Page 98 and 99: Creating a Patch Stretch Tune Depth
Page 100 and 101: Creating a Patch Portamento Switch
Page 102 and 103: Creating a Patch fig.06-020 fig.06-
Page 104 and 105: Creating a Patch Key Fade Upper (Ke
Page 106 and 107: Creating a Patch FXM Color 106 Spec
Page 108 and 109: Creating a Patch Pitch Keyfollow fi
Page 110 and 111: Creating a Patch Cutoff Frequency
Page 112 and 113: Creating a Patch F-Env T4 V-Sens (T
Page 114 and 115: Creating a Patch Bias Direction 114
Page 116 and 117: Creating a Patch Output Settings Pa
Page 118 and 119: Creating a Patch Delay Time (LFO1/L
Page 120 and 121: Creating a Patch ● Apply the LFO
Page 122 and 123: Creating a Patch Patch Mtrx Control
Page 124 and 125: Creating a Patch ● Changing the D
Page 126 and 127: Creating a Rhythm Set Tone Pitch Be
Page 128 and 129: Creating a Rhythm Set Wave Level 12
Page 130 and 131: Creating a Rhythm Set Rhythm Pitch
Page 132 and 133: Creating a Rhythm Set Cutoff V-Curv
Page 134 and 135: Creating a Rhythm Set Random Pan De
Page 136 and 137: 136 Creating a Performance With the
Page 140 and 141: Creating a Performance Key Fade Low
Page 142 and 143: Creating a Performance Equal Temper
Page 144 and 145: 144 Adding Effects This section exp
Page 146 and 147: Adding Effects Functions of Effect
Page 148 and 149: Adding Effects Reverb Output 14 Rev
Page 150 and 151: Adding Effects Chorus Source 150 Se
Page 152 and 153: System Settings 152 System Control
Page 154 and 155: fig.VS-700R-block.eps 154 VS-700R B
Page 156 and 157: Installing the ARX Expansion Board
Page 158 and 159: Installing the ARX Expansion Board
Page 160 and 161: Installation de la carte d’expans
Page 162 and 163: Installation de la carte d’expans
Page 164 and 165: 164 Using only the VS-700C Console
Page 166 and 167: 166 Connecting Two VS-700R I/O Unit
Page 168 and 169: fig.38.eps 168 Connecting an EDIROL
Page 170 and 171: About V-LINK Settings for SONAR 170
Page 172 and 173: 172 Specifications VS-700C, VS-700R
Page 174 and 175: Specifications 962a 174 Dimensions
Page 176 and 177: Index flag ........................
Page 178 and 179: Index WORDCLOCK OUT Connector .....
Page 180 and 181: Index (Fantom VS) Patch ...........
Page 182 and 183: Index (Fantom VS) Receive Program C
Page 184 and 185: MEMO 184
Page 186 and 187: 186 For EU Countries UK DE FR IT ES
Page 188:
* 5 1 0 0 0 0 2 2 4 6 - 0 1 *
show all

Owner's Manual - Roland

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?