User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

More documents

Recommendations

Info

5 Programming Tool Movements TNC 360 5.1 General Information on Programming Tool Movements ................. 5-2 5.2 Contour Approach and Departure ...................................................... 5-4 Starting and end positions ........................................................................................... 5-4 Smooth approach and departure ................................................................................. 5-6 5.3 Path Functions ...................................................................................... 5-7 General information ..................................................................................................... 5-7 Machine axis movement under program control ........................................................ 5-7 Overview of path functions ......................................................................................... 5-9 5.4 Path Contours - Cartesian Coordinates ............................................ 5-10 Straight line at rapid traverse G00 ............................................................................. 5-10 Straight line with feed rate G01 F ... ......................................................................... 5-10 Chamfer G24 ............................................................................................................. 5-13 Circles and circular arcs - General information .......................................................... 5-15 Circle center I, J, K ................................................................................................... 5-16 Circular path G02/G03/G05 around the circle center I, J, K ...................................... 5-18 Circular path G02/G03/G05 with defined radius ........................................................ 5-21 Circular path G06 with tangential connection............................................................ 5-24 Corner rounding G25 ................................................................................................. 5-26 5.5 Path Contours - Polar Coordinates ................................................... 5-28 Polar coordinate origin: Pole I, J, K ........................................................................... 5-28 Straight line at rapid traverse G10 ............................................................................. 5-28 Straight line with feed rate G11 F ... ......................................................................... 5-28 Circular path G12/G13/G15 around pole I, J, K .......................................................... 5-30 Circular path G16 with tangential connection............................................................ 5-32 Helical interpolation ................................................................................................... 5-33 5.6 M Functions for Contouring Behavior and Coordinate Data.......... 5-36 Smoothing corners: M90 ........................................................................................... 5-36 Machining small contour steps: M97 ........................................................................ 5-37 Machining open contours: M98 ................................................................................ 5-38 Programming machine-referenced coordinates: M91/M92 ...................................... 5-39 5.7 Positioning with Manual Data Input (MDI) ...................................... 5-41
6 Subprograms and Program Section Repeats TNC 360 6.1 Subprograms ........................................................................................ 6-2 Principle ...................................................................................................................... 6-2 Operating limits ........................................................................................................... 6-2 Programming and calling subprograms ....................................................................... 6-3 6.2 Program Section Repeats .................................................................... 6-5 Principle ...................................................................................................................... 6-5 Programming notes ..................................................................................................... 6-5 Programming and calling a program section repeat .................................................... 6-5 6.3 Main Program as Subprogram ............................................................ 6-8 Principle ...................................................................................................................... 6-8 Operating limits ........................................................................................................... 6-8 To call a main program as a subprogram .................................................................... 6-8 6.4 Nesting .................................................................................................. 6-9 Nesting depth .............................................................................................................. 6-9 Subprogram in a subprogram ...................................................................................... 6-9 Repeating program section repeats .......................................................................... 6-11 Repeating subprograms ............................................................................................ 6-12
Page 1 and 2: February 1994 HEIDENHAIN User's Man
Page 3 and 4: TNC Guideline: From workpiece drawi
Page 5 and 6: How to use this manual TNC 360 This
Page 7 and 8: Contents User's Manual TNC 360 ISO
Page 9 and 10: 2 Manual Operation and Setup TNC 36
Page 11: 4 Programming TNC 360 4.1 Editing P
Page 15 and 16: 8 Cycles TNC 360 8.1 General Overvi
Page 17 and 18: 10 MOD Functions TNC 360 10.1 Selec
Page 19 and 20: 1 Introduction 1.1 The TNC 360 1-2
Page 21 and 22: 1 Introduction 1.1 The TNC 360 1-4
Page 23 and 24: 1 Introduction 1.2 Fundamentals of
Page 31 and 32: 1 Introduction 1.3 Switch-On 1-14 S
Page 33 and 34: 1 Introduction 1.4 Graphics and Sta
Page 35 and 36: 1 Introduction 1.4 Graphics and Sta
Page 37 and 38: 1 Introduction 1.5 Programs Selecti
Page 39 and 40: 2 Manual Operation and Setup 2.1 Mo
Page 41 and 42: 2 Manual Operation and Setup 2.1 Mo
Page 43 and 44: 2 Manual Operation and Setup 2.2 Sp
Page 45 and 46: 2 Manual Operation and Setup 2.3 Se
Page 47 and 48: 2 Manual Operation and Setup 2.4 3D
Page 49 and 50: 2 Manual Operation and Setup 2.4 3D
Page 57 and 58: 2 Manual Operation and Setup 2.6 Me
Page 59 and 60: 2 Manual Operation and Setup 2.6 Me
Page 61 and 62: 3 Test Run and Program Run 3.2 Prog
Page 63 and 64:
3 Test Run and Program Run 3.2 Prog
Page 65 and 66:
3 Test Run and Program Run 3.3 Bloc
Page 67 and 68:
4 Programming 4.1 Editing Part Prog
Page 69 and 70:
4 Programming 4.2 Tools TNC 360 Eac
Page 71 and 72:
4 Programming 4.2 Tools Entering to
Page 73 and 74:
4 Programming 4.2 Tools Calling too
Page 75 and 76:
4 Programming 4.3 Tool Compensation
Page 77 and 78:
4 Programming 4.3 Tool Compensation
Page 79 and 80:
4 Programming 4.4 Program Creation
Page 81 and 82:
4 Programming 4.5 Entering Tool-Rel
Page 83 and 84:
4 Programming 4.6 Entering Miscella
Page 85 and 86:
5 Programming Tool Movements 5.1 Ge
Page 87 and 88:
5 Programming Tool Movements 5.2 Co
Page 89 and 90:
5 Programming Tool Movements 5.2 Co
Page 91 and 92:
5 Programming Tool Movements 5.3 Pa
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
5 Programming Tool Movements 5.6 M
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
6 Subprograms and Program Section R
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
7 Programming with Q Parameters 7.1
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
8 Cycles 8.1 General Overview of Cy
Page 157 and 158:
8 Cycles 8.2 Simple Fixed Cycles PE
Page 159 and 160:
8 Cycles 8.2 Simple Fixed Cycles TA
Page 161 and 162:
8 Cycles 8.2 Simple Fixed Cycles RI
Page 163 and 164:
8 Cycles 8.2 Simple Fixed Cycles 8-
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
8 Cycles 8.3 SL Cycles CONTOUR GEOM
Page 171 and 172:
8 Cycles 8.3 SL Cycles 8-18 Example
Page 173 and 174:
8 Cycles 8.3 SL Cycles 8-20 Cycle i
Page 175 and 176:
8 Cycles 8.3 SL Cycles 8-22 Subprog
Page 177 and 178:
Page 179 and 180:
8 Cycles 8.3 SL Cycles CONTOUR MILL
Page 181 and 182:
Page 183 and 184:
8 Cycles 8.4 Cycles for Coordinate
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
8 Cycles 8.5 Other Cycles DWELL TIM
Page 193 and 194:
9 External Data Transfer 9-2 The TN
Page 195 and 196:
9 External Data Transfer 9.3 Prepar
Page 197 and 198:
10 MOD Functions 10.3 Entering the
Page 199 and 200:
10 MOD Functions 10.7 Selecting the
Page 201 and 202:
11 Tables, Overviews, Diagrams 11.1
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227:
11 Tables, Overviews, Diagrams 11-2
show all

User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?