User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

More documents

Recommendations

Info

11 Tables, Overviews, Diagrams 11.1 General User Parameters TNC 360 Integrating the TNC interfaces to external devices: Data format and transmission stop Input value: number between 0 and 255 The entry value is the sum of the individual values. MP5020 Function Selections Value • Number of data bits 7 data bits (ASCII code, 8th bit = parity) .................................... +0 8 data bits (ASCII code, 9th bit = parity) .................................... +1 • Block Check Character (BCC) BCC can be any character ............................................................ +0 BCC control character not allowed ............................................... +2 • Transmission stop with RTS Active ........................................................................................... +4 Inactive ......................................................................................... +0 • Transmission stop with DC3 Active ........................................................................................... +8 Inactive ......................................................................................... +0 • Character parity Even ............................................................................................. +0 Odd ............................................................................................. +16 • Character parity Not desired ................................................................................... +0 Desired ....................................................................................... +32 • Number of stop bits 1 1 / 2 stop bits ................................................................................ +0 2 stop bits .............................................................................. +64 1 stop bit .............................................................................. +128 1 stop bit .............................................................................. +192 Example To adapt the TNC interface to an external non- HEIDENHAIN device, use the following setting: 8 data bits, BCC any character, transmission stop with DC3, even character parity, character parity desired, 2 stop bits. Input value: 1+0+8+0+32+64 = 105, so enter 105 for MP 5020. Interface type MP5030 Function Selections Value • Interface type Standard .......................................................................................... 0 Interface for blockwise transfer ...................................................... 1 11-3
11 Tables, Overviews, Diagrams 11.1 General User Parameters Parameters for 3D touch probes 11-4 Signal transmission type MP6010 Function Value • Cable transmission...........................................................................................................................................0 • Infrared transmission ....................................................................................................................................... 1 Traversing behavior of touch probe Parameter Function Value MP6120 Probing feed rate in mm/min ............................................................... 80 to 30 000 MP6130 Maximum measuring range to first scanning point in mm .................... 0 to 30 000 MP6140 Safety clearance over probing point during automatic probing, in mm ........................................................... 0 to 30 000 MP6150 Rapid traverse for probe cycle in mm/min ........................................... 80 to 30 000 Parameters for TNC displays and the editor Programming station MP7210 Function Value • TNC with machine ...........................................................................................................................................0 • TNC as programming station with active PLC ................................................................................................. 1 • TNC as programming station with inactive PLC .............................................................................................. 2 TNC 360
Page 1 and 2:
February 1994 HEIDENHAIN User's Man
Page 3 and 4:
TNC Guideline: From workpiece drawi
Page 5 and 6:
How to use this manual TNC 360 This
Page 7 and 8:
Contents User's Manual TNC 360 ISO
Page 9 and 10:
2 Manual Operation and Setup TNC 36
Page 11 and 12:
4 Programming TNC 360 4.1 Editing P
Page 13 and 14:
6 Subprograms and Program Section R
Page 15 and 16:
8 Cycles TNC 360 8.1 General Overvi
Page 17 and 18:
10 MOD Functions TNC 360 10.1 Selec
Page 19 and 20:
1 Introduction 1.1 The TNC 360 1-2
Page 21 and 22:
1 Introduction 1.1 The TNC 360 1-4
Page 23 and 24:
1 Introduction 1.2 Fundamentals of
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
1 Introduction 1.3 Switch-On 1-14 S
Page 33 and 34:
1 Introduction 1.4 Graphics and Sta
Page 35 and 36:
1 Introduction 1.4 Graphics and Sta
Page 37 and 38:
1 Introduction 1.5 Programs Selecti
Page 39 and 40:
2 Manual Operation and Setup 2.1 Mo
Page 41 and 42:
2 Manual Operation and Setup 2.1 Mo
Page 43 and 44:
2 Manual Operation and Setup 2.2 Sp
Page 45 and 46:
2 Manual Operation and Setup 2.3 Se
Page 47 and 48:
2 Manual Operation and Setup 2.4 3D
Page 49 and 50:
2 Manual Operation and Setup 2.4 3D
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
2 Manual Operation and Setup 2.6 Me
Page 59 and 60:
2 Manual Operation and Setup 2.6 Me
Page 61 and 62:
3 Test Run and Program Run 3.2 Prog
Page 63 and 64:
3 Test Run and Program Run 3.2 Prog
Page 65 and 66:
3 Test Run and Program Run 3.3 Bloc
Page 67 and 68:
4 Programming 4.1 Editing Part Prog
Page 69 and 70:
4 Programming 4.2 Tools TNC 360 Eac
Page 71 and 72:
4 Programming 4.2 Tools Entering to
Page 73 and 74:
4 Programming 4.2 Tools Calling too
Page 75 and 76:
4 Programming 4.3 Tool Compensation
Page 77 and 78:
4 Programming 4.3 Tool Compensation
Page 79 and 80:
4 Programming 4.4 Program Creation
Page 81 and 82:
4 Programming 4.5 Entering Tool-Rel
Page 83 and 84:
4 Programming 4.6 Entering Miscella
Page 85 and 86:
5 Programming Tool Movements 5.1 Ge
Page 87 and 88:
5 Programming Tool Movements 5.2 Co
Page 89 and 90:
5 Programming Tool Movements 5.2 Co
Page 91 and 92:
5 Programming Tool Movements 5.3 Pa
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
5 Programming Tool Movements 5.6 M
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
7 Programming with Q Parameters 7.1
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152: 7 Programming with Q Parameters 7.8
Page 153 and 154: 7 Programming with Q Parameters 7.8
Page 155 and 156: 8 Cycles 8.1 General Overview of Cy
Page 157 and 158: 8 Cycles 8.2 Simple Fixed Cycles PE
Page 159 and 160: 8 Cycles 8.2 Simple Fixed Cycles TA
Page 161 and 162: 8 Cycles 8.2 Simple Fixed Cycles RI
Page 163 and 164: 8 Cycles 8.2 Simple Fixed Cycles 8-
Page 169 and 170: 8 Cycles 8.3 SL Cycles CONTOUR GEOM
Page 171 and 172: 8 Cycles 8.3 SL Cycles 8-18 Example
Page 173 and 174: 8 Cycles 8.3 SL Cycles 8-20 Cycle i
Page 175 and 176: 8 Cycles 8.3 SL Cycles 8-22 Subprog
Page 179 and 180: 8 Cycles 8.3 SL Cycles CONTOUR MILL
Page 183 and 184: 8 Cycles 8.4 Cycles for Coordinate
Page 191 and 192: 8 Cycles 8.5 Other Cycles DWELL TIM
Page 193 and 194: 9 External Data Transfer 9-2 The TN
Page 195 and 196: 9 External Data Transfer 9.3 Prepar
Page 197 and 198: 10 MOD Functions 10.3 Entering the
Page 199 and 200: 10 MOD Functions 10.7 Selecting the
Page 201: 11 Tables, Overviews, Diagrams 11.1
Page 205 and 206: 11 Tables, Overviews, Diagrams 11.1
Page 227: 11 Tables, Overviews, Diagrams 11-2
show all

User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?