User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

More documents

Recommendations

Info

4 Programming 4.2 Tools 4-10 Tool change position A tool change position must lie next to or above the workpiece to prevent tool collision. With the miscellaneous functions M91 and M92 (see page 5- 39) you can enter machine-referenced rather than workpiecereferenced coordinates for the tool change position. If T0 is programmed before the first tool call, the TNC moves the spindle to an uncompensated position. If a positive length compensation value was in effect before T0, the clearance to the workpiece is reduced. TNC 360
4 Programming 4.3 Tool Compensation Values TNC 360 For each tool, the TNC adjusts the spindle path in the tool axis by the compensation value for the tool length. In the working plane it compensates the tool radius. Effect of tool compensation values Tool length Length compensation becomes effective automatically as soon as a tool is called and the tool axis moves. To cancel length compensation, call a tool with the length L = 0. Tool radius Radius compensation becomes effective as soon as a tool is called and is moved in the working plane with G41 or G42. To cancel radius compensation, program a positioning block with G40. Tool radius compensation Tool traverse can be programmed: • Without radius compensation: G40 • With radius compensation: G41or G42 • As single-axis movements with G43 or G44 Fig. 4.4: The TNC must compensate the length and radius of the tool R Fig. 4.5: Programmed contour (–––, +) and the path of the tool center (- - -) R 4-11
Page 1 and 2:
February 1994 HEIDENHAIN User's Man
Page 3 and 4:
TNC Guideline: From workpiece drawi
Page 5 and 6:
How to use this manual TNC 360 This
Page 7 and 8:
Contents User's Manual TNC 360 ISO
Page 9 and 10:
2 Manual Operation and Setup TNC 36
Page 11 and 12:
4 Programming TNC 360 4.1 Editing P
Page 13 and 14:
6 Subprograms and Program Section R
Page 15 and 16:
8 Cycles TNC 360 8.1 General Overvi
Page 17 and 18:
10 MOD Functions TNC 360 10.1 Selec
Page 19 and 20:
1 Introduction 1.1 The TNC 360 1-2
Page 21 and 22:
1 Introduction 1.1 The TNC 360 1-4
Page 23 and 24: 1 Introduction 1.2 Fundamentals of
Page 31 and 32: 1 Introduction 1.3 Switch-On 1-14 S
Page 33 and 34: 1 Introduction 1.4 Graphics and Sta
Page 35 and 36: 1 Introduction 1.4 Graphics and Sta
Page 37 and 38: 1 Introduction 1.5 Programs Selecti
Page 39 and 40: 2 Manual Operation and Setup 2.1 Mo
Page 41 and 42: 2 Manual Operation and Setup 2.1 Mo
Page 43 and 44: 2 Manual Operation and Setup 2.2 Sp
Page 45 and 46: 2 Manual Operation and Setup 2.3 Se
Page 47 and 48: 2 Manual Operation and Setup 2.4 3D
Page 49 and 50: 2 Manual Operation and Setup 2.4 3D
Page 57 and 58: 2 Manual Operation and Setup 2.6 Me
Page 59 and 60: 2 Manual Operation and Setup 2.6 Me
Page 61 and 62: 3 Test Run and Program Run 3.2 Prog
Page 63 and 64: 3 Test Run and Program Run 3.2 Prog
Page 65 and 66: 3 Test Run and Program Run 3.3 Bloc
Page 67 and 68: 4 Programming 4.1 Editing Part Prog
Page 69 and 70: 4 Programming 4.2 Tools TNC 360 Eac
Page 71 and 72: 4 Programming 4.2 Tools Entering to
Page 73: 4 Programming 4.2 Tools Calling too
Page 77 and 78: 4 Programming 4.3 Tool Compensation
Page 79 and 80: 4 Programming 4.4 Program Creation
Page 81 and 82: 4 Programming 4.5 Entering Tool-Rel
Page 83 and 84: 4 Programming 4.6 Entering Miscella
Page 85 and 86: 5 Programming Tool Movements 5.1 Ge
Page 87 and 88: 5 Programming Tool Movements 5.2 Co
Page 89 and 90: 5 Programming Tool Movements 5.2 Co
Page 91 and 92: 5 Programming Tool Movements 5.3 Pa
Page 119 and 120: 5 Programming Tool Movements 5.6 M
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
7 Programming with Q Parameters 7.1
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
8 Cycles 8.1 General Overview of Cy
Page 157 and 158:
8 Cycles 8.2 Simple Fixed Cycles PE
Page 159 and 160:
8 Cycles 8.2 Simple Fixed Cycles TA
Page 161 and 162:
8 Cycles 8.2 Simple Fixed Cycles RI
Page 163 and 164:
8 Cycles 8.2 Simple Fixed Cycles 8-
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
8 Cycles 8.3 SL Cycles CONTOUR GEOM
Page 171 and 172:
8 Cycles 8.3 SL Cycles 8-18 Example
Page 173 and 174:
8 Cycles 8.3 SL Cycles 8-20 Cycle i
Page 175 and 176:
8 Cycles 8.3 SL Cycles 8-22 Subprog
Page 177 and 178:
Page 179 and 180:
8 Cycles 8.3 SL Cycles CONTOUR MILL
Page 181 and 182:
Page 183 and 184:
8 Cycles 8.4 Cycles for Coordinate
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
8 Cycles 8.5 Other Cycles DWELL TIM
Page 193 and 194:
9 External Data Transfer 9-2 The TN
Page 195 and 196:
9 External Data Transfer 9.3 Prepar
Page 197 and 198:
10 MOD Functions 10.3 Entering the
Page 199 and 200:
10 MOD Functions 10.7 Selecting the
Page 201 and 202:
11 Tables, Overviews, Diagrams 11.1
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227:
11 Tables, Overviews, Diagrams 11-2
show all

User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

Create successful ePaper yourself

Delete template?

Save as template?