User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

More documents

Recommendations

Info

5 Programming Tool Movements 5.7 Positioning with Manual Data Input (MDI) TNC 360 In the POSITIONING WITH MANUAL DATA INPUT mode of operation you can use G07 to enter and execute single-axis positioning blocks. The entered positioning blocks are not stored in the TNC memory. Application examples: • Pre-positioning • Face milling F POSITIONING MANUAL DATA INPUT Select the MDI function. G 7 G 9 X 5 0 1 5 0 0 END I Select a single axis positioning block. For example: Select programming absolute values. For example: Position in X at 5 mm. For example: Feed rate F=1500 mm/min; terminate the block. Start the positioning block. 5-41
6 Subprograms and Program Section Repeats 6 Subprograms and Program Section Repeats 6-2 Subprograms and program section repeats enable you to program a machining sequence once and then run it as often as you wish. Labels Subprograms and program section repeats are marked by labels. A label carries a number from 0 to 254. Each label number (except 0) can only appear once in a program. Labels are assigned with the command G98. LABEL 0 marks the end of a subprogram. 6.1 Subprograms Principle The (main) program is executed up to the block in which the subprogram is called with Ln,0 ( 1 ). Then the subprogram is executed from beginning to end (G98 L0) ( 2 ). Finally, the main program is resumed from the block after the subprogram call ( 3 ). Operating limits • One main program can contain up to 254 subprograms. • Subprograms can be called in any sequence and as often as desired. • A subprogram cannot call itself. • Subprograms should be located at the end of the main program (after the block with M2 or M30). • If subprograms are located in the program before the block with M02 or M30, they will be executed at least once even without being called. N1 % ... * . . . . . . . . . . . . . . 1 L1, 0 * 3 Z + 100 M2 * G98 L1 * 2 G98 L0 * N9999 % ... * Fig. 6.1: Flow diagram for a subprogram; S = jump, R = return jump R S TNC 360
Page 1 and 2:
February 1994 HEIDENHAIN User's Man
Page 3 and 4:
TNC Guideline: From workpiece drawi
Page 5 and 6:
How to use this manual TNC 360 This
Page 7 and 8:
Contents User's Manual TNC 360 ISO
Page 9 and 10:
2 Manual Operation and Setup TNC 36
Page 11 and 12:
4 Programming TNC 360 4.1 Editing P
Page 13 and 14:
6 Subprograms and Program Section R
Page 15 and 16:
8 Cycles TNC 360 8.1 General Overvi
Page 17 and 18:
10 MOD Functions TNC 360 10.1 Selec
Page 19 and 20:
1 Introduction 1.1 The TNC 360 1-2
Page 21 and 22:
1 Introduction 1.1 The TNC 360 1-4
Page 23 and 24:
1 Introduction 1.2 Fundamentals of
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
1 Introduction 1.3 Switch-On 1-14 S
Page 33 and 34:
1 Introduction 1.4 Graphics and Sta
Page 35 and 36:
1 Introduction 1.4 Graphics and Sta
Page 37 and 38:
1 Introduction 1.5 Programs Selecti
Page 39 and 40:
2 Manual Operation and Setup 2.1 Mo
Page 41 and 42:
2 Manual Operation and Setup 2.1 Mo
Page 43 and 44:
2 Manual Operation and Setup 2.2 Sp
Page 45 and 46:
2 Manual Operation and Setup 2.3 Se
Page 47 and 48:
2 Manual Operation and Setup 2.4 3D
Page 49 and 50:
2 Manual Operation and Setup 2.4 3D
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
2 Manual Operation and Setup 2.6 Me
Page 59 and 60:
2 Manual Operation and Setup 2.6 Me
Page 61 and 62:
3 Test Run and Program Run 3.2 Prog
Page 63 and 64:
3 Test Run and Program Run 3.2 Prog
Page 65 and 66:
3 Test Run and Program Run 3.3 Bloc
Page 67 and 68:
4 Programming 4.1 Editing Part Prog
Page 69 and 70:
4 Programming 4.2 Tools TNC 360 Eac
Page 71 and 72:
4 Programming 4.2 Tools Entering to
Page 73 and 74: 4 Programming 4.2 Tools Calling too
Page 75 and 76: 4 Programming 4.3 Tool Compensation
Page 77 and 78: 4 Programming 4.3 Tool Compensation
Page 79 and 80: 4 Programming 4.4 Program Creation
Page 81 and 82: 4 Programming 4.5 Entering Tool-Rel
Page 83 and 84: 4 Programming 4.6 Entering Miscella
Page 85 and 86: 5 Programming Tool Movements 5.1 Ge
Page 87 and 88: 5 Programming Tool Movements 5.2 Co
Page 89 and 90: 5 Programming Tool Movements 5.2 Co
Page 91 and 92: 5 Programming Tool Movements 5.3 Pa
Page 119 and 120: 5 Programming Tool Movements 5.6 M
Page 121 and 122: 5 Programming Tool Movements 5.6 M
Page 123: 5 Programming Tool Movements 5.6 M
Page 127 and 128: 6 Subprograms and Program Section R
Page 137 and 138: 7 Programming with Q Parameters 7.1
Page 155 and 156: 8 Cycles 8.1 General Overview of Cy
Page 157 and 158: 8 Cycles 8.2 Simple Fixed Cycles PE
Page 159 and 160: 8 Cycles 8.2 Simple Fixed Cycles TA
Page 161 and 162: 8 Cycles 8.2 Simple Fixed Cycles RI
Page 163 and 164: 8 Cycles 8.2 Simple Fixed Cycles 8-
Page 169 and 170: 8 Cycles 8.3 SL Cycles CONTOUR GEOM
Page 171 and 172: 8 Cycles 8.3 SL Cycles 8-18 Example
Page 173 and 174: 8 Cycles 8.3 SL Cycles 8-20 Cycle i
Page 175 and 176:
8 Cycles 8.3 SL Cycles 8-22 Subprog
Page 177 and 178:
8 Cycles 8.3 SL Cycles 8-24 Example
Page 179 and 180:
8 Cycles 8.3 SL Cycles CONTOUR MILL
Page 181 and 182:
8 Cycles 8.3 SL Cycles 8-28 Example
Page 183 and 184:
8 Cycles 8.4 Cycles for Coordinate
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
8 Cycles 8.5 Other Cycles DWELL TIM
Page 193 and 194:
9 External Data Transfer 9-2 The TN
Page 195 and 196:
9 External Data Transfer 9.3 Prepar
Page 197 and 198:
10 MOD Functions 10.3 Entering the
Page 199 and 200:
10 MOD Functions 10.7 Selecting the
Page 201 and 202:
11 Tables, Overviews, Diagrams 11.1
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227:
11 Tables, Overviews, Diagrams 11-2
show all

User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

Create successful ePaper yourself

Delete template?

Save as template?