User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

More documents

Recommendations

Info

8 Cycles 8.4 Cycles for Coordinate Transformations TNC 360 Example: Datum shift A machining sequence in the form of a subprogram is to be executed twice: a) once, referenced to the specified datum 1 X+0/Y+0 and b) a second time, referenced to the shifted datum 2 X+40/Y+60. Cycle in a part program %S840I G71 * ............................................................ Begin program N10 G30 G17 X+0 Y+0 Z–20 * ................................... Define workpiece blank N20 G31 X+100 Y+100 Z+0 * N30 G99 T1 L+0 R+4 * .............................................. Tool definition N40 T1 G17 S1500 * .................................................. Tool call N50 G00 G40 G90 Z+100 * ........................................ Retract the tool N60 L1,0 * .................................................................. Execute sequence 1 without datum shift N70 G54 X+40 Y+60 * N80 L1,0 * .................................................................. Execute sequence 2 with datum shift N90 G54 X+0 Y+0 * ................................................... Cancellation of datum shift N100 Z+100 M02 * N110 G98 L1 * . . . N230 G98 L0 * N9999 %S840I G71 * Y 20 15 20 Y Z 40 1 Z 2 15 25 30 25 30 60 X X 8-31
8 Cycles 8.4 Cycles for Coordinate Transformations 8-32 Subprogram: N110 G98 L1 * N120 X–10 Y–10 M03 * N130 Z+2 * N140 G01 Z–5 F200 * N150 G41 X+0 Y+0 * N160 Y+20 * N170 X+25 * N180 X+30 Y+15 * N190 Y+0 * N200 X+0 * N210 G40 X–10 Y–10 * N220 G00 Z+2 * N230 G98 L0 * The location of the subprogram (NC block) depends on the transformation cycle: LBL 1 LBL 0 Datum shift block N110 block N230 Mirror image, rotation, scaling block N130 block N250 TNC 360
Page 1 and 2:
February 1994 HEIDENHAIN User's Man
Page 3 and 4:
TNC Guideline: From workpiece drawi
Page 5 and 6:
How to use this manual TNC 360 This
Page 7 and 8:
Contents User's Manual TNC 360 ISO
Page 9 and 10:
2 Manual Operation and Setup TNC 36
Page 11 and 12:
4 Programming TNC 360 4.1 Editing P
Page 13 and 14:
6 Subprograms and Program Section R
Page 15 and 16:
8 Cycles TNC 360 8.1 General Overvi
Page 17 and 18:
10 MOD Functions TNC 360 10.1 Selec
Page 19 and 20:
1 Introduction 1.1 The TNC 360 1-2
Page 21 and 22:
1 Introduction 1.1 The TNC 360 1-4
Page 23 and 24:
1 Introduction 1.2 Fundamentals of
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
1 Introduction 1.3 Switch-On 1-14 S
Page 33 and 34:
1 Introduction 1.4 Graphics and Sta
Page 35 and 36:
1 Introduction 1.4 Graphics and Sta
Page 37 and 38:
1 Introduction 1.5 Programs Selecti
Page 39 and 40:
2 Manual Operation and Setup 2.1 Mo
Page 41 and 42:
2 Manual Operation and Setup 2.1 Mo
Page 43 and 44:
2 Manual Operation and Setup 2.2 Sp
Page 45 and 46:
2 Manual Operation and Setup 2.3 Se
Page 47 and 48:
2 Manual Operation and Setup 2.4 3D
Page 49 and 50:
2 Manual Operation and Setup 2.4 3D
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
2 Manual Operation and Setup 2.6 Me
Page 59 and 60:
2 Manual Operation and Setup 2.6 Me
Page 61 and 62:
3 Test Run and Program Run 3.2 Prog
Page 63 and 64:
3 Test Run and Program Run 3.2 Prog
Page 65 and 66:
3 Test Run and Program Run 3.3 Bloc
Page 67 and 68:
4 Programming 4.1 Editing Part Prog
Page 69 and 70:
4 Programming 4.2 Tools TNC 360 Eac
Page 71 and 72:
4 Programming 4.2 Tools Entering to
Page 73 and 74:
4 Programming 4.2 Tools Calling too
Page 75 and 76:
4 Programming 4.3 Tool Compensation
Page 77 and 78:
4 Programming 4.3 Tool Compensation
Page 79 and 80:
4 Programming 4.4 Program Creation
Page 81 and 82:
4 Programming 4.5 Entering Tool-Rel
Page 83 and 84:
4 Programming 4.6 Entering Miscella
Page 85 and 86:
5 Programming Tool Movements 5.1 Ge
Page 87 and 88:
5 Programming Tool Movements 5.2 Co
Page 89 and 90:
5 Programming Tool Movements 5.2 Co
Page 91 and 92:
5 Programming Tool Movements 5.3 Pa
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
5 Programming Tool Movements 5.6 M
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134: 6 Subprograms and Program Section R
Page 135 and 136: 6 Subprograms and Program Section R
Page 137 and 138: 7 Programming with Q Parameters 7.1
Page 155 and 156: 8 Cycles 8.1 General Overview of Cy
Page 157 and 158: 8 Cycles 8.2 Simple Fixed Cycles PE
Page 159 and 160: 8 Cycles 8.2 Simple Fixed Cycles TA
Page 161 and 162: 8 Cycles 8.2 Simple Fixed Cycles RI
Page 163 and 164: 8 Cycles 8.2 Simple Fixed Cycles 8-
Page 169 and 170: 8 Cycles 8.3 SL Cycles CONTOUR GEOM
Page 171 and 172: 8 Cycles 8.3 SL Cycles 8-18 Example
Page 173 and 174: 8 Cycles 8.3 SL Cycles 8-20 Cycle i
Page 175 and 176: 8 Cycles 8.3 SL Cycles 8-22 Subprog
Page 179 and 180: 8 Cycles 8.3 SL Cycles CONTOUR MILL
Page 183: 8 Cycles 8.4 Cycles for Coordinate
Page 187 and 188: 8 Cycles 8.4 Cycles for Coordinate
Page 189 and 190: 8 Cycles 8.4 Cycles for Coordinate
Page 191 and 192: 8 Cycles 8.5 Other Cycles DWELL TIM
Page 193 and 194: 9 External Data Transfer 9-2 The TN
Page 195 and 196: 9 External Data Transfer 9.3 Prepar
Page 197 and 198: 10 MOD Functions 10.3 Entering the
Page 199 and 200: 10 MOD Functions 10.7 Selecting the
Page 201 and 202: 11 Tables, Overviews, Diagrams 11.1
Page 227: 11 Tables, Overviews, Diagrams 11-2
show all

User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

Create successful ePaper yourself

Delete template?

Save as template?