User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

More documents

Recommendations

Info

1 Introduction 1.5 Programs The TNC 360 can store up to 32 part programs at once. The part programs can be written in HEIDENHAIN plain language dialog or according to ISO. ISO programs are indicated with “ISO”. Each program is identified by a number with up to eight characters. Program directory The program directory is called with the PGM NR key. To erase programs in the TNC memory, press the CL PGM key. The program directory provides the following information: • Program number • Program type (HEIDENHAIN or ISO) • Program size in bytes, where one byte is the equivalent of one character. Action Mode of Call program operation directory with... Create (a program) ... Edit ... Erase ... Test ... Execute ... Fig. 1.29: Program management functions Fig. 1.30: Program directory on the TNC screen TNC 360 1-19 PGM NR PGM NR CL PGM PGM NR PGM NR
1 Introduction 1.5 Programs Selecting, erasing and protecting programs 1-20 To select a program: e.g. PGM NR PROGRAM NUMBER ? 1 or ENT To erase a program: ENT CL PGM or or PGM NR 5 ERASE = ENT / END = NO ENT To protect a program: G 5 5 ENT 0 NO ENT PROGRAM NUMBER = ? END Resulting NC block: %5 G71 G50 * Removing edit protection Call the program management. Use the arrow keys to highlight the program. Enter the desired program number, for example 15. Confirm your selection. Press CL PGM to call the program management. Use the arrow keys to highlight the program. Erase the program or abort. Call the program management. Enter the number of the program to be protected, for example program number 5. Use the arrow key to highlight the first block. To remove edit protection re-select the program and enter the code number 86357 with the corresponding MOD function (see page 10-3). Enter the function for program protection, conclude the block. TNC 360
Page 1 and 2: February 1994 HEIDENHAIN User's Man
Page 3 and 4: TNC Guideline: From workpiece drawi
Page 5 and 6: How to use this manual TNC 360 This
Page 7 and 8: Contents User's Manual TNC 360 ISO
Page 9 and 10: 2 Manual Operation and Setup TNC 36
Page 11 and 12: 4 Programming TNC 360 4.1 Editing P
Page 13 and 14: 6 Subprograms and Program Section R
Page 15 and 16: 8 Cycles TNC 360 8.1 General Overvi
Page 17 and 18: 10 MOD Functions TNC 360 10.1 Selec
Page 19 and 20: 1 Introduction 1.1 The TNC 360 1-2
Page 21 and 22: 1 Introduction 1.1 The TNC 360 1-4
Page 23 and 24: 1 Introduction 1.2 Fundamentals of
Page 31 and 32: 1 Introduction 1.3 Switch-On 1-14 S
Page 33 and 34: 1 Introduction 1.4 Graphics and Sta
Page 35: 1 Introduction 1.4 Graphics and Sta
Page 39 and 40: 2 Manual Operation and Setup 2.1 Mo
Page 41 and 42: 2 Manual Operation and Setup 2.1 Mo
Page 43 and 44: 2 Manual Operation and Setup 2.2 Sp
Page 45 and 46: 2 Manual Operation and Setup 2.3 Se
Page 47 and 48: 2 Manual Operation and Setup 2.4 3D
Page 49 and 50: 2 Manual Operation and Setup 2.4 3D
Page 57 and 58: 2 Manual Operation and Setup 2.6 Me
Page 59 and 60: 2 Manual Operation and Setup 2.6 Me
Page 61 and 62: 3 Test Run and Program Run 3.2 Prog
Page 63 and 64: 3 Test Run and Program Run 3.2 Prog
Page 65 and 66: 3 Test Run and Program Run 3.3 Bloc
Page 67 and 68: 4 Programming 4.1 Editing Part Prog
Page 69 and 70: 4 Programming 4.2 Tools TNC 360 Eac
Page 71 and 72: 4 Programming 4.2 Tools Entering to
Page 73 and 74: 4 Programming 4.2 Tools Calling too
Page 75 and 76: 4 Programming 4.3 Tool Compensation
Page 77 and 78: 4 Programming 4.3 Tool Compensation
Page 79 and 80: 4 Programming 4.4 Program Creation
Page 81 and 82: 4 Programming 4.5 Entering Tool-Rel
Page 83 and 84: 4 Programming 4.6 Entering Miscella
Page 85 and 86: 5 Programming Tool Movements 5.1 Ge
Page 87 and 88:
5 Programming Tool Movements 5.2 Co
Page 89 and 90:
5 Programming Tool Movements 5.2 Co
Page 91 and 92:
5 Programming Tool Movements 5.3 Pa
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
5 Programming Tool Movements 5.6 M
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
6 Subprograms and Program Section R
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
7 Programming with Q Parameters 7.1
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
8 Cycles 8.1 General Overview of Cy
Page 157 and 158:
8 Cycles 8.2 Simple Fixed Cycles PE
Page 159 and 160:
8 Cycles 8.2 Simple Fixed Cycles TA
Page 161 and 162:
8 Cycles 8.2 Simple Fixed Cycles RI
Page 163 and 164:
8 Cycles 8.2 Simple Fixed Cycles 8-
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
8 Cycles 8.3 SL Cycles CONTOUR GEOM
Page 171 and 172:
8 Cycles 8.3 SL Cycles 8-18 Example
Page 173 and 174:
8 Cycles 8.3 SL Cycles 8-20 Cycle i
Page 175 and 176:
8 Cycles 8.3 SL Cycles 8-22 Subprog
Page 177 and 178:
Page 179 and 180:
8 Cycles 8.3 SL Cycles CONTOUR MILL
Page 181 and 182:
Page 183 and 184:
8 Cycles 8.4 Cycles for Coordinate
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
8 Cycles 8.5 Other Cycles DWELL TIM
Page 193 and 194:
9 External Data Transfer 9-2 The TN
Page 195 and 196:
9 External Data Transfer 9.3 Prepar
Page 197 and 198:
10 MOD Functions 10.3 Entering the
Page 199 and 200:
10 MOD Functions 10.7 Selecting the
Page 201 and 202:
11 Tables, Overviews, Diagrams 11.1
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227:
11 Tables, Overviews, Diagrams 11-2
show all

User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?