User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

More documents

Recommendations

Info

7 Programming with Q Parameters 7.8 Examples for Exercise Rectangular pocket with corner rounding and tangential approach 7-14 Pocket center coordinates X = 50 mm (Q1) Y = 50 mm (Q2) Pocket length X = 90 mm (Q3) Pocket width Y = 70 mm (Q4) Working depth Z = (–) 15 mm (–Q5) Corner radius R = 10 mm (Q6) Milling feed F = 200 mm/min (Q7) Note: At corners 21 and 31 the workpiece will be machined slightly differently than shown in the drawing! Part program %360077 G71 * N10 G30 G17 X+0 Y+0 Z–20 * Program start and workpiece blank N20 G31 G90 X+100 Y+100 Z+0 * N30 D00 Q01 P01 +50 * N40 D00 Q02 P01 +50 * N50 D00 Q03 P01 +90 * N60 D00 Q04 P01 +70 * Assign the rectangular pocket data to Q parameters N70 D00 Q05 P01 +15 * N80 D00 Q06 P01 +10 * N90 D00 Q07 P01 +200 * N100 G99 T1 L+0 R+5 * N110 T1 G17 S1000 * Define and insert the tool N120 G00 G40 G90 Z+100 M6 * N130 D04 P01 Q13 P02 +Q03 P03 +2 * Enter half the pocket length and width for the paths of N140 D04 P01 Q14 P02 +Q04 P03 +2 * traverse in blocks N200, N220, N300 N150 D04 P01 Q16 P02 +Q06 P03 +4 * ................... Rounding radius for smooth approach N160 D04 P01 Q17 P02 +Q07 P03 +2 * ................... Feed rate in corners is half the rate for linear movement N170 X+Q01 Y+Q02 M03 * ....................................... Pre-position in X and Y (pocket center), spindle ON N180 Z+2 * ................................................................. Pre-position over workpiece N190 G01 Z–Q05 FQ07 * ........................................... Move to working depth Q5 (= –15 mm) with feed rate Q7 (= 100) N200 G41 G91 X+Q13 G90 Y+Q02 * N210 G26 RQ16 * Approach the pocket in a tangential arc N220 G91 Y+Q14 * N230 G25 RQ6 FQ17 * N240 X–Q3 * N250 G25 RQ6 FQ17 * N260 Y-Q4 * Mill the frame of the rectangular pocket N270 G25 RQ6 FQ17 * N280 X+Q3 * N290 G25 RQ6 FQ17 * N300 Y+Q14 * N310 G27 RQ16 * Depart to pocket center in a tangential arc N320 G00 G40 G90 X+Q1 Y+Q2 * N330 Z+100 M02 * .................................................... Retract tool N9999 %360077 G71 * 26 27 28 29 32 31 17 25 24 20 30 21 23 22 TNC 360
7 Programming with Q Parameters 7.8 Examples for Exercise Bolt hole circles TNC 360 Bore pattern 1 distributed over a full circle: Entry values are listed below in program blocks N10 to N80. Movements in the plane are programmed with polar coordinates. Bore pattern 2 distributed over a circle sector: Entry values are listed below in blocks N150 to N190; Q5, Q7 and Q8 remain the same. The holes are executed with cycle G83: PECKING (see page 8-4) Part program 70 Y 1 30 90 %3600715 G71 * ....................................................... Load data for bolt hole circle 1 N10 D00 Q01 P01 +30 * ............................................ Circle center X coordinate N20 D00 Q02 P01 +70 * ............................................ Circle center Y coordinate N30 D00 Q03 P01 +11 * ............................................ Number of holes N40 D00 Q04 P01 +25 * ............................................ Circle radius N50 D00 Q05 P01 +90 * ............................................ Starting angle N60 D00 Q06 P01 +0 * .............................................. Hole angle increment (0: distribute holes over 360°) N70 D00 Q07 P01 +2 * .............................................. Setup clearance N80 D00 Q08 P01 +15 * ............................................ Total hole depth N90 G30 G17 X+0 Y+0 Z-20 * N100 G31 G90 X+100 Y+100 Z+0 * N110 G99 T1 L+0 R+4 * N120 T1 G17 S2500 * N130 G83 P01 -Q07 ................................................... Definition of the pecking cycle/setup clearance P02 -Q08.......................................................... Total hole depth according to the load data P03 -5 .............................................................. Pecking depth P04 0 ............................................................... Dwell time P05 250 * ........................................................ Feed rate for pecking N140 L1,0 * ................................................................ Call bolt hole circle 1 Load data for bolt hole circle 2 (only re-enter changed data) N150 D00 Q1 P01 +90 * ............................................ New circle center X coordinate N160 D00 Q2 P01 +25 * ............................................ New circle center Y coordinate N170 D00 Q3 P01 +5 * .............................................. New number of holes N180 D00 Q4 P01 +35 * ............................................ New circle radius N190 D00 Q6 P01 +30 * ............................................ New hole angle increment (not a full circle, 5 holes at 30° intervals) N200 L1,0 * ................................................................ Call bolt hole circle 2 N210 G00 G40 G90 Z+200 M02 * ............................. End of main program 25 90° 35 30° 2 25 X Continued... 7-15
Page 1 and 2:
February 1994 HEIDENHAIN User's Man
Page 3 and 4:
TNC Guideline: From workpiece drawi
Page 5 and 6:
How to use this manual TNC 360 This
Page 7 and 8:
Contents User's Manual TNC 360 ISO
Page 9 and 10:
2 Manual Operation and Setup TNC 36
Page 11 and 12:
4 Programming TNC 360 4.1 Editing P
Page 13 and 14:
6 Subprograms and Program Section R
Page 15 and 16:
8 Cycles TNC 360 8.1 General Overvi
Page 17 and 18:
10 MOD Functions TNC 360 10.1 Selec
Page 19 and 20:
1 Introduction 1.1 The TNC 360 1-2
Page 21 and 22:
1 Introduction 1.1 The TNC 360 1-4
Page 23 and 24:
1 Introduction 1.2 Fundamentals of
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
1 Introduction 1.3 Switch-On 1-14 S
Page 33 and 34:
1 Introduction 1.4 Graphics and Sta
Page 35 and 36:
1 Introduction 1.4 Graphics and Sta
Page 37 and 38:
1 Introduction 1.5 Programs Selecti
Page 39 and 40:
2 Manual Operation and Setup 2.1 Mo
Page 41 and 42:
2 Manual Operation and Setup 2.1 Mo
Page 43 and 44:
2 Manual Operation and Setup 2.2 Sp
Page 45 and 46:
2 Manual Operation and Setup 2.3 Se
Page 47 and 48:
2 Manual Operation and Setup 2.4 3D
Page 49 and 50:
2 Manual Operation and Setup 2.4 3D
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
2 Manual Operation and Setup 2.6 Me
Page 59 and 60:
2 Manual Operation and Setup 2.6 Me
Page 61 and 62:
3 Test Run and Program Run 3.2 Prog
Page 63 and 64:
3 Test Run and Program Run 3.2 Prog
Page 65 and 66:
3 Test Run and Program Run 3.3 Bloc
Page 67 and 68:
4 Programming 4.1 Editing Part Prog
Page 69 and 70:
4 Programming 4.2 Tools TNC 360 Eac
Page 71 and 72:
4 Programming 4.2 Tools Entering to
Page 73 and 74:
4 Programming 4.2 Tools Calling too
Page 75 and 76:
4 Programming 4.3 Tool Compensation
Page 77 and 78:
4 Programming 4.3 Tool Compensation
Page 79 and 80:
4 Programming 4.4 Program Creation
Page 81 and 82:
4 Programming 4.5 Entering Tool-Rel
Page 83 and 84:
4 Programming 4.6 Entering Miscella
Page 85 and 86:
5 Programming Tool Movements 5.1 Ge
Page 87 and 88:
5 Programming Tool Movements 5.2 Co
Page 89 and 90:
5 Programming Tool Movements 5.2 Co
Page 91 and 92:
5 Programming Tool Movements 5.3 Pa
Page 93 and 94:
Page 95 and 96:
Page 97 and 98: 5 Programming Tool Movements 5.4 Pa
Page 119 and 120: 5 Programming Tool Movements 5.6 M
Page 125 and 126: 6 Subprograms and Program Section R
Page 137 and 138: 7 Programming with Q Parameters 7.1
Page 147: 7 Programming with Q Parameters 7.7
Page 155 and 156: 8 Cycles 8.1 General Overview of Cy
Page 157 and 158: 8 Cycles 8.2 Simple Fixed Cycles PE
Page 159 and 160: 8 Cycles 8.2 Simple Fixed Cycles TA
Page 161 and 162: 8 Cycles 8.2 Simple Fixed Cycles RI
Page 163 and 164: 8 Cycles 8.2 Simple Fixed Cycles 8-
Page 169 and 170: 8 Cycles 8.3 SL Cycles CONTOUR GEOM
Page 171 and 172: 8 Cycles 8.3 SL Cycles 8-18 Example
Page 173 and 174: 8 Cycles 8.3 SL Cycles 8-20 Cycle i
Page 175 and 176: 8 Cycles 8.3 SL Cycles 8-22 Subprog
Page 179 and 180: 8 Cycles 8.3 SL Cycles CONTOUR MILL
Page 183 and 184: 8 Cycles 8.4 Cycles for Coordinate
Page 191 and 192: 8 Cycles 8.5 Other Cycles DWELL TIM
Page 193 and 194: 9 External Data Transfer 9-2 The TN
Page 195 and 196: 9 External Data Transfer 9.3 Prepar
Page 197 and 198: 10 MOD Functions 10.3 Entering the
Page 199 and 200:
10 MOD Functions 10.7 Selecting the
Page 201 and 202:
11 Tables, Overviews, Diagrams 11.1
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227:
11 Tables, Overviews, Diagrams 11-2
show all

User's Manual ISO TNC 360 (260020xx, 280490xx) - heidenhain

Create successful ePaper yourself

Delete template?

Save as template?