Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-98 Marine/Industrial 4.3L Engine Valve Lifters and Guides Clean and Inspect Important: Parts that are to be reused must be marked, sorted and organized for assembly. 1. Mark, sort and organize the components for assembly. Caution: Refer to Safety Glasses Caution in Cautions and Notices. 2. Clean the components with cleaning solvent. 3. Dry the components with compressed air. 188118 4. Inspect the valve lifter pushrod guides for excessive wear. 5. Inspect the valve lifter pushrod guides for cracks or damage. 334500 6. Inspect the valve lifter for the following: • Broken or damaged clip (1) • Worn pushrod socket (2) • Scuffed or worn lifter body (3) If the valve lifter shows scuffing or wear, inspect the engine block valve lifter bores for wear. • Worn roller (4) • Loose or damaged pin (5) • Plugged oil hole (6) 2000 Marine/Industrial 178485
Engine Marine/Industrial 4.3L 6-99 Cylinder Head Disassemble Tools Required J 8062 Valve Spring Compressor Caution: Compressed valve springs have high tension against the valve spring compressor. Valve springs that are not properly compressed by or released from the valve spring compressor can be ejected from the valve spring compressor with intense force. Use care when compressing or releasing the valve spring with the valve spring compressor and when removing or installing the valve stem keys. Failing to use care may cause personal injury. Caution: Refer to Safety Glasses Caution in Cautions and Notices. 1. Use the J 8062 in order to compress the valve springs. Important: Mark, sort and organize the components so that the components can be reinstalled in their original location and position. 2. Remove the valve stem keys (1). 3. Remove the J 8062 from the cylinder head. 4. Remove the valve spring cap (2). 5. Remove the valve spring (3). 6. Remove the valve stem oil seal (4). 7. Discard the valve stem oil seal. 8. Remove the valve. 480554 Cylinder Head Clean and Inspect Tools Required J 8001 Dial Indicator Set J 8089 Carbon Removing Brush J 9666 Valve Spring Tester Caution: Refer to Safety Glasses Caution in Cautions and Notices. 1. Clean the valve stems and cylinder heads on a buffing wheel. 2. Clean the following components in cleaning solvent: • Valve stem keys (1) • Valve spring cap (2) • Valve spring (3) • Cylinder head 480555 480555 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18:
Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20:
Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22:
Engine Marine/Industrial 4.3L 6-11
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58: Engine Marine/Industrial 4.3L 6-47
Page 107: Engine Marine/Industrial 4.3L 6-97
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Notes
Page 195 and 196:
Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

Create successful ePaper yourself

Delete template?

Save as template?