Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-144 Marine/Industrial 4.3L Engine Notice: Refer to Fastener Notice in Cautions and Notices. Important: Do not use a hammer to install the camshaft sprocket onto the camshaft. To do so may dislodge the expansion cup plug (camshaft rear bearing hole). 7. Install the camshaft sprocket bolts. Tighten Tighten the camshaft sprocket bolts to 25 N•m (18 lb ft). 480544 7. Install the crankshaft position sensor reluctor ring. 7.1. Align the keyway on the crankshaft position sensor reluctor ring with the crankshaft balancer key in the crankshaft. 7.2. Use the J 5590 in order to push the crankshaft position sensor reluctor ring onto the crankshaft until completely seated against the crankhshaft sproket. 480576 Engine Front Cover Installation Important: Once the composite engine front cover is removed, DO NOT reinstall the engine front cover. Always install a NEW engine front cover. 1. Install the NEW engine front cover. Notice: Refer to Fasteners Notice in Cautions and Notices. 2. Install the engine front cover bolts. Tighten Tighten the engine front cover bolts to 12 N•m (106 lb in). 2000 Marine/Industrial 480539
Engine Marine/Industrial 4.3L 6-145 Important: DONOT reuse the original crankshaft position sensor seal (o-ring). When installing the crankshaft position sensor, be sure the crankshaft position sensor is fully seated and held stationary in the engine front cover crankshaft position sensor bore. A crankshaft position sensor that is not completely seated will cock in the engine front cover and may result in erratic engine operation. 3. Lubricate the NEW crankshaft position sensor seal (O-ring) with clean engine oil. 4. Install the NEW crankshaft position sensor seal (O-ring) onto the crankshaft position sensor. 5. Install the crankshaft position sensor until fully seated into the engine front cover. 6. Install the crankshaft position sensor bolt. Tighten Tighten the crankshaft position bolt to 8 N•m (71 lb in). 387759 Oil Pump Installation 1. Inspect for properly installed pins (oil pump locator). 11485 330578 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18:
Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20:
Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22:
Engine Marine/Industrial 4.3L 6-11
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104: Engine Marine/Industrial 4.3L 6-93
Page 153: Engine Marine/Industrial 4.3L 6-143
Page 193 and 194: Notes
Page 195 and 196: Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

Create successful ePaper yourself

Delete template?

Save as template?