Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-160 Marine/Industrial 4.3L Engine 5. Install the lower intake manifold onto the engine block. Notice: Refer to Fastener Notice in Cautions and Notices. 6. If reusing the fasteners, apply threadlock GM P/N 12345382 or equivalent to the threads of the lower intake manifold bolts. 7. Install the lower intake manifold bolts. 31510 Notice: Proper lower intake manifold fastener tightening sequence and torque is critical. Always follow the tightening sequence, and torque the intake manifold bolts using the 3 step method. Failing to do so may distort the crankshaft bearing bore alignment and cause damage to the crankshaft bearings. 8. Tighten the lower intake manifold bolts. Tighten 8.1. Tighten the bolts in sequence (1-8) on the first pass to 3 N•m (27 lb in). 8.2. Tighten the bolts in sequence (1-8) on the first pass to 12 N•m (106 lb in). 8.3. Tighten the bolts in sequence (1-8) on the first pass to 15 N•m (11 lb ft). 188150 9. Connect the evaporative emission (EVAP) canister solenoid valve harness. 9.1. Push the elbow inward until the quick connect snaps into place. 9.2. Pull the elbow outward in order to ensure proper connection. 2000 Marine/Industrial 328579
Engine Marine/Industrial 4.3L 6-161 Distributor Installation Important: The engine front cover has 2 alignment tabs and the crankshaft balancer has 2 alignment marks (spaced 90 degrees apart) which are used for positioning number 1 piston at Top Dead Center (TDC). With the piston on the compression stroke and at top dead center, the crankshaft balancer alignment mark (1) must align with the engine front cover tab (2) and the crankshaft balancer alignment mark (4) must align with the engine front cover tab (3). Rotate the crankshaft balancer clockwise until the alignment marks on the crankshaft balancer are aligned with the tabs on the engine front cover and the number 1 piston is at top dead center of the compression stroke. 1. Remove the distributor cap bolts and discard. 2. Remove the distributor cap. 334551 3. Install a NEW distributor gasket onto the distributor. 301393 523516 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18:
Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20:
Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22:
Engine Marine/Industrial 4.3L 6-11
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120: Engine Marine/Industrial 4.3L 6-109
Page 169: Engine Marine/Industrial 4.3L 6-159
Page 193 and 194: Notes
Page 195 and 196: Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

Create successful ePaper yourself

Delete template?

Save as template?