Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-170 Marine/Industrial 4.3L Engine 1. Install the engine flywheel (1) or (2) to the crankshaft. Align the engine flywheel locator hole to the flywheel locator pin. 188129 Notice: Refer to Fastener Notice in Cautions and Notices. 2. Install the engine flywheel bolts. Tighten Tighten the engine flywheel bolts in sequence (1-6) to 100 N•m (74 lb ft). 63174 2000 Marine/Industrial
Engine Marine/Industrial 4.3L 6-171 Engine Set-Up and Testing After overhaul, the engine must be tested before it is installed in the vehicle. If a suitable test stand is not available, the following procedures can be used after the engine is installed in the vehicle. 1. Fill the crankcase with the proper quantity and grade of engine oil. 2. Add engine oil supplement GM P/N 1052367 or equivalent to the engine oil. Notice: DO NOT use cooling system seal tabs (or similar compounds) unless otherwise instructed. The use of cooling system seal tabs (or similar compounds) may restrict coolant flow through the passages of the cooling system or the engine components. Restricted coolant flow may cause engine overheating and/or damage to the cooling system or the engine components/assembly. 3. Fill the cooling system with the proper quantity and grade of coolant. 4. With the ignition OFF or disconnected, crank the engine several times. Listen for any unusual noises or evidence that any of the parts are binding. 5. Start the engine and listen for unusual noises. 6. Check the vehicle oil pressure gauge or light and confirm that the engine has acceptable oil pressure. If necessary, install an oil pressure gauge and measure the engine oil pressure. 7. Operate the engine at about 1,000 RPM until the engine has reached normal operating temperature. 8. Listen for improperly adjusted or sticking valves, sticking valve lifters or other unusual noises. 9. Inspect for oil and/or coolant leaks while the engine is operating. 10. Verify that the distributor is properly positioned. 11. Perform a final inspection for the proper engine oil and coolant levels. 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18:
Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20:
Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22:
Engine Marine/Industrial 4.3L 6-11
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130: Engine Marine/Industrial 4.3L 6-119
Page 179: Engine Marine/Industrial 4.3L 6-169
Page 193 and 194: Notes
Page 195 and 196: Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?