Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-138 Marine/Industrial 4.3L Engine 6. Remove the J 5239. 31373 Notice: Refer to Fastener Notice in Cautions and Notices. 7. Install the connecting rod caps, bearings and nuts. Tighten 7.1. Tighten the nuts evenly on the first pass to 27 N•m (20 lb ft). 7.2. Use the J 36660 in order to tighten the nuts on the final pass an additional 70 degrees. 480549 8. After the piston and connecting rod assemblies have been installed, then lightly tap each connecting rod assembly (parallel to the crankpin) in order to ensure that the connecting rods have side clearance. 9. Use a feeler gauge or a dial indicator to measure the connecting rod side clearance between the connecting rod caps. The connecting rod side clearance should be 0.15- 0.44 mm (0.006-0.017 in). 2000 Marine/Industrial 5163
Engine Marine/Industrial 4.3L 6-139 Camshaft Installation 1. Apply clean engine oil GM P/N 12345610 or equivalent, or engine oil supplement GM P/N 1052367 or equivalent to the following components: • The engine camshaft lobes • The camshaft bearing journals • The camshaft bearings 2. Install three 5/16-18 x 4.0 in. bolts into the engine camshaft front bolt holes. Notice: All camshaft journals are the same diameter, so care must be used in removing or installing the camshaft to avoid damage to the camshaft bearings. 3. Use the bolts as a handle in order to install the engine camshaft. 4. Remove the 3 bolts from the front of the engine camshaft. Notice: Refer to Fastener Notice in Cautions and Notices. 5. If reusing the fasteners, apply threadlock GM P/N 12345382 or equivalent to the threads of the camshaft retainer bolts. 6. Install the camshaft retainer and bolts. Tighten the camshaft retainer bolts to 12 N•m (106 lb in). 5147 Balance Shaft Installation Tools Required J 8092 Universal Driver Handle J 36660 Electronic Torque Angle Meter J 36996 Balance Shaft Installer Important: The balance shaft and the balance shaft front bearing are serviced only as an assembly. Do not remove the balance shaft front bearing from the balance shaft. 1. Apply clean engine oil GM P/N 12345610 or equivalent to the balance shaft front bearing. Caution: Refer to Safety Glasses Caution in Cautions and Notices. 2. Use the J 36996 and the J 8092 in order to install the balance shaft. 188030 5141 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18:
Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20:
Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22:
Engine Marine/Industrial 4.3L 6-11
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98: Engine Marine/Industrial 4.3L 6-87
Page 147: Engine Marine/Industrial 4.3L 6-137
Page 193 and 194: Notes
Page 195 and 196: Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

Create successful ePaper yourself

Delete template?

Save as template?