Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-86 Marine/Industrial 4.3L Engine 334387 Crankshaft Balancer Clean and Inspect Caution: Refer to Safety Glasses Caution in Cautions and Notices. 1. Clean the crankshaft balancer in cleaning solvent. 2. Dry the crankshaft balancer with compressed air. 3. Inspect the crankshaft balancer for the following: • Loose or improperly installed front groove pin (1) (crankshaft balancer) A properly installed front groove pin should be installed until flush or below flush with the face of the crankshaft balancer. Important: A crankshaft front oil sealing surface with excessive scoring, grooves, rust or other damage must be replaced. • Worn, grooved or damaged crankshaft front oil sealing surface (2) Minor imperfections on the crankshaft balancer crankshaft front oil seal surface may be removed with a polishing compound or fine grade emery cloth. • Worn, chunking or deteriorated rubber (3) between the hub and the outer ring • Worn or damaged keyway (4) • Worn or damaged bolt hole threads (5) Engine Flywheel Clean and Inspect Caution: Refer to Safety Glasses Caution in Cautions and Notices. 1. Clean the engine flywheel (1) or (2) in cleaning solvent. 2. Dry the engine flywheel with compressed air. 188129 2000 Marine/Industrial
Engine Marine/Industrial 4.3L 6-87 3. Inspect the engine flywheel (automatic transmission) (if equipped) for the following: • Stress cracks around the engine flywheel-to-torque converter bolt hole locations (1) • Missing balance weights • Stress cracks around the engine flywheel-to-crankshaft bolt hole locations (2) or (3) Important: Do not attempt to repair the welded areas (if present) that retain the ring gear to the engine flywheel plate. Always install a NEW engine flywheel. • Welded areas that retain the ring gear onto the engine flywheel for cracking (4) (if present) • Damaged ring gear teeth (5) 4. Inspect the engine flywheel (manual transmission) (if equipped) for loose or improperly installed flywheel weights (if applicable). A properly installed flywheel weight should be installed until flush or below flush with the face of the engine flywheel. 381965 5. Inspect the engine flywheel (manual transmission) (if equipped) for the following: • Pitted friction surface (1) • Scoring or grooves (2) • Rust or other surface damage (3) • Damaged ring gear teeth (4) • Loose or improperly positioned ring gear The ring gear has an interference fit onto the engine flywheel and the ring gear should be positioned completely flat against the flange of the engine flywheel. 64126 188086 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18:
Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20:
Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22:
Engine Marine/Industrial 4.3L 6-11
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46: Engine Marine/Industrial 4.3L 6-35
Page 95: Engine Marine/Industrial 4.3L 6-85
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Notes
Page 195 and 196:
Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

Create successful ePaper yourself

Delete template?

Save as template?