Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-152 Marine/Industrial 4.3L Engine Cylinder Head Installation (Left) Tools Required J 36660 Electronic Torque Angle Meter 1. Clean the cylinder head gasket surfaces on the engine block. 2. Inspect the dowel pins (cylinder head locators) for proper installation. 3. Clean the cylinder head gasket surfaces on the cylinder head. 334303 Important: Do not use any type of sealer on the cylinder head gasket (unless specified). 4. Install the NEW cylinder head gasket in position over the dowel pins (cylinder head locators). 334299 5. Install the cylinder head onto the engine block. Guide the cylinder head carefully into place over the dowel pins and the cylinder head gasket. 2000 Marine/Industrial 480536
Engine Marine/Industrial 4.3L 6-153 6. Apply sealant GM P/N 12346004 or equivalent to the threads of the cylinder head bolts. Notice: Refer to Fastener Notice in Cautions and Notices. 7. Install the cylinder head bolts finger tight. 8. Tighten the cylinder head bolts in sequence on the first pass. Tighten Tighten the bolts in sequence on the first pass to 30 N•m (22 lb ft). 9. Use the J 36660 in order to tighten the cylinder head bolts in sequence on the final pass. • Tighten the long bolts (1,4,5,8 and 9) on the final pass in sequence to 75 degrees. • Tighten the medium bolts (12 and 13) on the final pass in sequence to 65 degrees. • Tighten the short bolts (2,3,6,7,10 and 11) on the final pass in sequence to 55 degrees. 480533 10. Install the spark plug wire support and bolts. Tighten Tighten the spark plug wire support bolts to 12 N•m (106 lb in). 5132 328588 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18:
Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20:
Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22:
Engine Marine/Industrial 4.3L 6-11
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112: Engine Marine/Industrial 4.3L 6-101
Page 161: Engine Marine/Industrial 4.3L 6-151
Page 193 and 194: Notes
Page 195 and 196: Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

Create successful ePaper yourself

Delete template?

Save as template?