Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-58 Marine/Industrial 4.3L Engine Notice: All camshaft journals are the same diameter, so care must be used in removing or installing the camshaft to avoid damage to the camshaft bearings. 2. Remove the engine camshaft. 2.1. Install the three 5/16-18 x 4.0 inch bolts into the engine camshaft front bolt holes. 2.2. Using the bolts as a handle, carefully rotate and pull the engine camshaft out of the camshaft bearings. 2.3. Remove the bolts from the front of the engine camshaft. 5147 11497 Piston, Connecting Rod, and Bearing Removal Tools Required • J 5239 Conneting Rod Bolt Guide Set • J 24270 Cylinder Bore Ridge Reamer 1. Use the J 24270 in order to remove the cylinder ring ridge. 1.1. Turn the crankshaft until the piston is at the bottom of the stroke. 1.2. Place a cloth on top of the piston. 1.3. Use the J 24270 to remove all of the cylinder ring ridge. 1.4. Turn the crankshaft so the piston is at the top of the stroke. 1.5. Remove the cloth. 1.6. Remove the cutting debris. Important: Place matchmarks or numbers on the connecting rods and the connecting rod caps. 2. Remove the connecting rod nuts. 3. Remove the connecting rod cap. 480549 2000 Marine/Industrial
Engine Marine/Industrial 4.3L 6-59 4. Use the J 5239 in order to protect the crankshaft journals and remove the connecting rod and the piston out of the top of the engine block. Important: Always assemble the connecting rod caps to the matching connecting rods. 5. Remove the connecting rod bearings. 5.1. Keep the connecting rod bearings with the original connecting rod and connecting rod cap. 5.2. Wipe the oil from the connecting rod bearings. 5.3. Wipe the oil from the crankpins. 31373 Crankshaft Rear Oil Seal and Housing Removal 1. Remove the crankshaft rear oil seal from the crankshaft rear oil seal housing. 2. Insert a suitable tool into the access notches and then carefully pry the crankshaft rear oil seal from the crankshaft rear oil seal housing. 3. Discard the crankshaft rear oil seal. 188017 31379 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18: Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20: Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22: Engine Marine/Industrial 4.3L 6-11
Page 67: Engine Marine/Industrial 4.3L 6-57
Page 119 and 120:
Engine Marine/Industrial 4.3L 6-109
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Notes
Page 195 and 196:
Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?