Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-118 Marine/Industrial 4.3L Engine 5. Inspect the upper intake manifold for the following: • Cracks or other damage to the exterior (1) • Cracking or damage in the gasket grooves (2) and (3) • Damage to the throttle body mounting surface (4) • Loose or damaged bolt hole thread inserts (5) 480569 6. Inspect the lower intake manifold for the following: • Damage to the gasket sealing surfaces (1), (2) and (3) • Restricted exhaust gas recirculation (EGR) system passages • Restricted cooling system passages (5) • Cracks or damage • Damage to the threaded bolt holes 480570 Intake Manifold Assemble Notice: Refer to Fastener Notice in Cautions and Notices. 1. If reusing the fastener, apply threadlock GM P/N 12345382 or equivalent to the threads of the fuel meter body bracket bolt. 2. Install the fuel meter body bracket and bolt. Tighten Tighten the fuel meter body bracket bolt to 10 N•m (89 lb in). 3. Install the fuel meter body into the fuel meter body bracket. 4. Install the 6 poppet nozzles into the proper lower intake manifold bores. 5. Inspect the poppet nozzles in order to ensure that the poppet nozzles are firmly seated and locked in the lower intake manifold bores. 2000 Marine/Industrial 523513
Engine Marine/Industrial 4.3L 6-119 6. Install a NEW fuel meter body seal into the groove of the fuel meter body. 7. Install NEW upper intake manifold to lower intake manifold gasket into the groove of the upper intake manifold. 8. Install the upper intake manifold onto the lower intake manifold. 9. If reusing the fasteners, apply threadlock GM P/N 12345382 or equivalent to the threads of the upper intake manifold attaching studs. 10. Install the upper intake manifold attaching studs. Tighten 10.1. Tighten the upper intake manifold attaching studs on the first pass to 5 N•m (44 lb in). 10.2. Tighten the upper intake manifold attaching studs on the final pass to 9 N•m (80 lb in). 11. If reusing the fasteners, apply threadlock GM P/N 12345382 or equivalent to the threads of the evaporative emission (EVAP) canister purge solenoid valve studs. 12. Install the EVAP canister purge solenoid valve and studs. Tighten Tighten the EVAP canister purge solenoid valve studs to 10 N•m (89 lb in). 334516 334511 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18:
Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20:
Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22:
Engine Marine/Industrial 4.3L 6-11
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78: Engine Marine/Industrial 4.3L 6-67
Page 127: Engine Marine/Industrial 4.3L 6-117
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Notes
Page 195 and 196:
Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

Create successful ePaper yourself

Delete template?

Save as template?