Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-124 Marine/Industrial 4.3L Engine 4. Measure the alignment or surface flatness of the exhaust manifold flanges using a straight edge and a feeler gauge. Refer to Engine Mechanical Specifications. If the surface flatness is not within the specifications, the exhaust manifold is warped and must be replaced. 334528 480571 Water Pump Clean and Inspect Caution: Refer to Safety Glasses Caution in Cautions and Notices. 1. Remove all the old gasket material from the water pump sealing surfaces. 2. Clean all the dirt and any debris from the water pump. 3. Inspect the water pump for the following: • Leakage or damage to the housing cover or gasket (1) • Excessive scratches or gouging to the gasket sealing surfaces (2) • Leakage from the water pump vent hole (3) A stain around the vent hole is acceptable. If leakage occurred (dripping) with the engine operating and the cooling system pressurized, then replace the water pump. • Damaged bolt hole threads (4) • Excessive side-to-side movement of the water pump shaft (5) • Leakage around the water inlet pipe (6) • Leakage around the heater hose pipe (7) • Restrictions within the internal coolant passages 2000 Marine/Industrial
Engine Marine/Industrial 4.3L 6-125 Thread Repair General purpose thread repair kits are available commercially. Caution: Refer to Safety Glasses Caution in Cautions and Notices. Important: Refer to the thread repair kit manufacturer’s instructions regarding the size of the drill and which tap to use. Always avoid any buildup of chips. Back out the tap every few turns and remove the chips. Determine the size, the pitch and the depth of the damaged thread. 1. Adjust the stop collars on the cutting tool as needed. Tap the stop collars to the required depths. 2. Drill out the damaged thread. 3. Remove the chips. 4. Apply clean engine oil to the top thread. 5. Use the tap in order to cut new thread. 6. Clean the thread. 7. Screw the thread insert onto the mandrel of the thread insert installer. Engage the tang of the thread insert onto the end of the mandrel. Important: The thread insert should be flush to 1 turn below the surface. 8. Lubricate the thread insert with clean engine oil (except when installing in aluminum) and install the thread insert. 9. If the tang of the thread insert does not break off when backing out the thread insert installer, break off the tang using a drift punch. 4962 4963 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18:
Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20:
Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22:
Engine Marine/Industrial 4.3L 6-11
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84: Engine Marine/Industrial 4.3L 6-73
Page 133: Engine Marine/Industrial 4.3L 6-123
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Notes
Page 195 and 196:
Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

Create successful ePaper yourself

Delete template?

Save as template?