Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

More documents

Recommendations

Info

6-148 Marine/Industrial 4.3L Engine Notice: Refer to Fastener Notice in Cautions and Notices. 6. Install the oil pan bolts and nuts, but do not tighten. 7. Measure the pan-to-transmission housing clearance using a feeler gauge and a straight edge. Use a feeler gauge to check the clearance between the oil pan-to-transmission housing measurement points. If the clearance exceeds 0.3 mm (0.011 in) at any of the 3 oil panto-transmission housing measurement points (1), then repeat the step until the oil pan-to-transmission housing clearance is within the specification. The oil pan must always be forward of the rear face of the engine block. 38496 Notice: If the clearance is more than 0.3 mm (0.011 in), powertrain durability may be reduced. 8. Tighten the oil pan bolts and nuts in sequence (1-12). Tighten Tighten the oil pan bolts to 25 N•m (18 lb ft). 9. Measure the clearance between the 3 oil pan-totransmission housing measurement points in order to ensure proper alignment. 38481 10. Install a NEW oil pan drain plug seal (O-ring) onto the oil pan drain plug. 11. Install the oil pan drain plug into the oil pan. Tighten Tighten the oil pan drain plug to 25 N•m (18 lb ft). 2000 Marine/Industrial 188048
Engine Marine/Industrial 4.3L 6-149 12. Install the NEW engine oil level sensor (if applicable). Tighten Tighten the engine oil level sensor to 13 N•m (115 lb in). Crankshaft Balancer Installation Tools Required J 23523-F Balancer Remover and Installer 1. Look to ensure that the front groove pin (crankshaft balancer) is installed in the proper location (if applicable). 387460 Notice: The inertial weight section of the crankshaft balancer is assembled to the hub with a rubber type material. The correct installation procedures (with the proper tool) must be followed or movement of the inertial weight section of the hub will destroy the tuning of the crankshaft balancer. 2. Apply a small amount of adhesive GM P/N 12346141 or equivalent onto the crankshaft balancer keyway in order to seal the crankshaft balancer keyway and crankshaft joint. 3. Align the keyway of the crankshaft balancer with the crankshaft balancer key. 4. Install the crankshaft balancer onto the end of the crankshaft. 334258 188059 2000 Marine/Industrial
Page 1 and 2:
Service Engine Engine Model: Genera
Page 3 and 4:
Table of Contents Caution Introduct
Page 5 and 6:
Table of Contents, continued Valve
Page 7 and 8:
Introduction This service manual pr
Page 9 and 10:
Cautions and Notices Definition of
Page 11 and 12:
Engine Marine/Industrial 4.3L 6-1 E
Page 13 and 14:
Engine Marine/Industrial 4.3L 6-3 F
Page 15 and 16:
Engine Marine/Industrial 4.3L 6-5 E
Page 17 and 18:
Engine Marine/Industrial 4.3L 6-7 G
Page 19 and 20:
Engine Marine/Industrial 4.3L 6-9 G
Page 21 and 22:
Engine Marine/Industrial 4.3L 6-11
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108: Engine Marine/Industrial 4.3L 6-97
Page 157: Engine Marine/Industrial 4.3L 6-147
Page 193 and 194: Notes
Page 195 and 196: Notes
show all

Service Manual, General Motors 4.3L Engine (TP ... - Kohler Power

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?