Getting Started SURFCAM

More documents

Recommendations

Info

Step 4: Chamfer the edges Chamfering is useful for removing burrs, trimming sharp edges, or adding a relief angle. For this project, you will add a 0.075-inch 45° chamfer around the top edge of the outer part profile using a 0.25-inch chamfer tool. 1 On the NC menu, click 2 Axis and then click Chamfer Mill 2 Create a chain on the part profile and then click Done 88 | Get <strong>Started</strong> with <strong>SURFCAM</strong>
3 Select the 0.2500 diameter, 45 degree Chamfer tool and click OK 4 Enter 6 for the Tool Number, Length Offset, and Diameter Offset Project 2 • Mill a Production Part | 89
Page 2 and 3:
Get Started with SURFCAM Copyright
Page 4 and 5:
Step 1: Face the material .........
Page 6 and 7:
System Requirements The following o
Page 8 and 9:
SURFCAM Help SURFCAM provides onlin
Page 10 and 11:
toolbars. If you select No Text Lab
Page 12 and 13:
The SURFCAM Status Toolbar The butt
Page 14 and 15:
Using SURFCAM SURFCAM is a computer
Page 16 and 17:
Use the Open command on the File me
Page 18 and 19:
To activate the change, you need to
Page 20 and 21:
Managing toolpaths Use the NC Opera
Page 22 and 23:
Generating NC code A CNC machine to
Page 24 and 25:
Creating and modifying geometry in
Page 26 and 27:
Icon Command Description Sketch Poi
Page 28 and 29:
Step 1: Draw the part profile The f
Page 30 and 31:
5 Click Keyboard 6 Enter 0.0 for al
Page 32 and 33:
4 Select the bottom line 5 Click in
Page 34 and 35:
Trim and fillet the corners of the
Page 36 and 37:
7 Click the Trim button until Trim
Page 38 and 39:
5 Select the beginning element as s
Page 40 and 41:
2 Click Center/Diameter 3 Enter a d
Page 42 and 43: 2 Click Offset 3 Click Change Offse
Page 44 and 45: 9 Click inside the profile to indic
Page 46 and 47: 2 Click Tangent 2 3 Click Change Ra
Page 48 and 49: 9 Select the lower half of the larg
Page 50 and 51: 14 Click Change Radius 15 Change th
Page 52 and 53: 4 Click Center 5 Select the circle
Page 54 and 55: 4 Click Sketch 5 Select the origin
Page 56 and 57: You have now completed drawing the
Page 58 and 59: 4 Click Keyboard 5 Set the dialog a
Page 60 and 61: Now you need to specify two locatio
Page 62 and 63: 9 Click Fit This project is now com
Page 64 and 65: SURFCAM 2 Axis Milling SURFCAM’s
Page 66 and 67: Icon Command Description Material P
Page 68 and 69: Before you begin Make sure your uni
Page 70 and 71: By default, Chain is selected on th
Page 72 and 73: 6 Enter 1 for the Tool Number and L
Page 74 and 75: 11 Click Accept 12 On the Main tool
Page 76 and 77: 4 Click Part 6 Click Auto 5 Select
Page 78 and 79: 11 Click the Cut Control tab 12 Set
Page 80 and 81: Step 3: Drill the holes A single dr
Page 82 and 83: 4 Select one of the drilled holes i
Page 84 and 85: 4 Click Select Tool 5 Select the .5
Page 86 and 87: 11 Click Add After 12 Click Select
Page 88 and 89: 16 Click the Cycle Control tab 17 S
Page 90 and 91: 24 Click the Sorting Control tab 25
Page 94 and 95: 5 Click the Cut Control tab 6 Enter
Page 96 and 97: Step 5: Verify the tool path Verifi
Page 98 and 99: 8 Click Run SURFCAM Verify The Veri
Page 100 and 101: 13 Click Play to start the verifica
Page 102 and 103: 3 Set the dialog as shown and click
Page 104 and 105: Now the generated code is shown in
Page 106 and 107: Creating and modifying surfaces in
Page 108 and 109: For this project you will learn how
Page 110 and 111: Next you will create a fillet surfa
Page 112 and 113: 12 Click Fillet 13 Change Fillet Ra
Page 114 and 115: 4 Click End Point 5 Select the end
Page 116 and 117: Step 3: Add the cover Next you will
Page 118 and 119: You will finish the cover by creati
Page 120 and 121: 5 Select the cover surface and the
Page 122 and 123: 4 On the Edit menu, click Trim/Brea
Page 124 and 125: 10 On the Create menu, click Surfac
Page 126 and 127: 15 Click Yes to create the blend su
Page 128 and 129: 22 Click End Point 23 Select the en
Page 130 and 131: SURFCAM 3 Axis Milling SURFCAM gene
Page 132 and 133: Step 1: Rough Surfaces Z Rough remo
Page 134 and 135: 8 Set the Cut Control tab as shown
Page 136 and 137: 12 Open the Operations Manager and
Page 138 and 139: 3 Click Select Tool and choose the
Page 140 and 141: 7 Click Sketch 8 Right-click on the
Page 142 and 143:
Step 3: Finish the lens housing You
Page 144 and 145:
4 Set the Cut Control tab as shown
Page 146 and 147:
Step 4: Trace the blend fillets You
Page 148 and 149:
5 Set the Cut Control tab as shown
Page 150 and 151:
Next you will create stock for veri
Page 152 and 153:
7 Click Run SURFCAM Verify Note: To
show all

Getting Started SURFCAM

Create successful ePaper yourself

Delete template?

Save as template?