Driver Installation Guide - Egmont Instruments

More documents

Recommendations

Info

The System Properties window will appear. Click on the Device Manager tab. You will see the following window: 24 Driver Installation Guide for CompuScope Cards
Double-click on Other devices. Underneath Other devices, you will now see the item PCI Card, as shown below. Installation / CompuScope Win 95/98 for PCI Cards 25
Page 1 and 2: Driver Installation Guide for Compu
Page 3 and 4: Table of Contents Preface..........
Page 5 and 6: Preface Gage’s CompuScope Drivers
Page 7 and 8: CompuScope Digital Input Cards Boar
Page 9 and 10: Chapter 1 - Installation Installati
Page 11 and 12: Windows 95 OR Windows 98 ISA Refer
Page 13 and 14: Installing CompuScope Hardware Turn
Page 15 and 16: Starting Gage Driver Disk Setup Pro
Page 17 and 18: Clicking on Next opens the Main Men
Page 19 and 20: Installing CompuScope Win 95/98 Dri
Page 21 and 22: The installation process will resum
Page 23: Installing CompuScope Win 95/98 Dri
Page 27 and 28: Make sure Other devices is highligh
Page 29 and 30: Click OK. You will now see two wind
Page 33 and 34: You will see the following dialog:
Page 35 and 36: If you have installed more than one
Page 39 and 40: installation process to terminate i
Page 41 and 42: The Setup Complete Window will be d
Page 43 and 44: Installing CompuScope Win 2000 Driv
Page 45 and 46: You will see the following dialog:
Page 47 and 48: The installation process will conti
Page 49 and 50: Installing CompuScope Win 2000 Driv
Page 51 and 52: You will see the following window:
Page 53 and 54: Add/Remove Hardware Wizard will ask
Page 55 and 56: From the list of available Models f
Page 57 and 58: Please make sure that you write dow
Page 59 and 60: Select Memory Range and click on Ch
Page 61 and 62: Note: Follow the same procedure out
Page 63 and 64: Installing CompuScope Win NT Driver
Page 65 and 66: Click Next to continue with the ins
Page 67 and 68: Installing GageScope ® for DOS Ins
Page 69 and 70: Note: You may click the Cancel butt
Page 71 and 72: The Setup Complete Window will be d
Page 73 and 74: Chapter 2 - Verifying Driver Instal
Page 75 and 76:
Which version of Gage Config do I h
Page 77 and 78:
Checking the Status of Your Board(s
Page 79 and 80:
Memory Conflict If the Board Name f
Page 81 and 82:
Resolving I/O Conflicts Note: This
Page 83 and 84:
How to Respecify I/O Addresses in G
Page 85 and 86:
The Status Box should now read Save
Page 87 and 88:
To resolve conflicts caused by memo
Page 89 and 90:
To try another memory base address,
Page 91 and 92:
Bus Speed Some BIOS’s allow non-s
Page 93 and 94:
Detailed Description of Gage Config
Page 95 and 96:
I/O Address Field Upon running Gage
Page 97 and 98:
Board Name Field If your board is f
Page 99 and 100:
Memory Size Field The Memory Size f
Page 101 and 102:
Add Button The Add button allows yo
Page 103 and 104:
Remove Button The Remove button all
Page 105 and 106:
Save Button The Save button saves t
Page 107 and 108:
Operation Mode Box The Operation Mo
Page 109 and 110:
Configuration File Box The Configur
Page 111 and 112:
Driver Version Button The Driver Ve
Page 113 and 114:
The AutoVerify checkbox allows you
Page 115 and 116:
If you click Add System without fir
Page 117 and 118:
Save All Button The Save All button
Page 119 and 120:
Close Button The Close button allow
Page 121 and 122:
Verifying Driver Installation with
Page 123 and 124:
While editing a field: or Moves
Page 125 and 126:
Setting the I/O and Memory Segment
Page 127 and 128:
Note: For CP500 boards, the final f
Page 129 and 130:
section I/O Addresses for CompuScop
Page 131 and 132:
386MAX, another popular memory mana
Page 133 and 134:
Because these CompuScope cards requ
Page 135 and 136:
Other Cards in your System Other ca
Page 137 and 138:
Chapter 3 - Verifying Signal Acquis
Page 139 and 140:
This will activate a second screen
Page 141 and 142:
Change the frequency of the signal
Page 143 and 144:
This short experiment proves that c
Page 145 and 146:
Verifying Signal Acquisition with G
Page 147 and 148:
Use the or + key to change the C
Page 149 and 150:
Chapter 4 - Uninstalling CompuScope
Page 151 and 152:
Double-click on System Devices. A w
Page 153 and 154:
2. Find and delete the .INF file th
Page 155 and 156:
Double-click on Class and the follo
Page 157 and 158:
In the right-hand portion of the wi
Page 159 and 160:
Uninstalling CompuScope Win 95/98 D
Page 161 and 162:
Click on . A window will appear ask
Page 163 and 164:
Uninstalling CompuScope Win 2000 Dr
Page 165 and 166:
You will see the following window:
Page 167 and 168:
The Add/Remove Hardware Wizard want
Page 169 and 170:
We will first make sure that all hi
Page 171 and 172:
Make sure that you select Show hidd
Page 173 and 174:
Double click on this file to open i
Page 175 and 176:
In the Window that appears, enter r
Page 177 and 178:
When you Click Permission, the foll
Page 179 and 180:
The Regedit window reappears: At th
Page 181 and 182:
Following window will appear. Type
Page 183 and 184:
Step 3B (GAGE ISA BUS CARDS ONLY) D
Page 185 and 186:
Step 3B (GAGE PCI BUS CARDS ONLY) D
Page 187 and 188:
Step 3C Double-click through the fo
Page 189 and 190:
Uninstalling GageScope ® for DOS T
Page 191 and 192:
Uninstalling CompuScope Win NT Driv
Page 193 and 194:
Chapter 5 - Files Copied in the Ins
Page 195 and 196:
Gage Products For ordering informat
show all

Driver Installation Guide - Egmont Instruments

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?