Driver Installation Guide - Egmont Instruments

More documents

Recommendations

Info

Once you select the desired location, click Next to continue with the installation, the Setup program will begin copying the necessary files to your computer. This will activate the following two windows which display the progress of the installation process: Once the Setup program has completed installing GageScope ® for DOS, the following window will be displayed: Click Yes to view the ReadMe file. This file contains the most recent information about GageScope ® for DOS. After viewing the ReadMe file, close your text viewer. 70 Driver Installation Guide for CompuScope Cards
The Setup Complete Window will be displayed: Click Finish to complete setup for GageScope ® for DOS. IMPORTANT NOTE: You should now proceed to the section entitled Verifying Driver Installation / GSINST on page 119. It is very important that you configure your card(s) after installing GageScope ® for DOS to ensure that your card(s) will operate properly. Installation / GageScope for DOS 71
Page 1 and 2:
Driver Installation Guide for Compu
Page 3 and 4:
Table of Contents Preface..........
Page 5 and 6:
Preface Gage’s CompuScope Drivers
Page 7 and 8:
CompuScope Digital Input Cards Boar
Page 9 and 10:
Chapter 1 - Installation Installati
Page 11 and 12:
Windows 95 OR Windows 98 ISA Refer
Page 13 and 14:
Installing CompuScope Hardware Turn
Page 15 and 16:
Starting Gage Driver Disk Setup Pro
Page 17 and 18:
Clicking on Next opens the Main Men
Page 19 and 20: Installing CompuScope Win 95/98 Dri
Page 21 and 22: The installation process will resum
Page 25 and 26: Double-click on Other devices. Unde
Page 27 and 28: Make sure Other devices is highligh
Page 29 and 30: Click OK. You will now see two wind
Page 33 and 34: You will see the following dialog:
Page 35 and 36: If you have installed more than one
Page 39 and 40: installation process to terminate i
Page 41 and 42: The Setup Complete Window will be d
Page 43 and 44: Installing CompuScope Win 2000 Driv
Page 45 and 46: You will see the following dialog:
Page 47 and 48: The installation process will conti
Page 49 and 50: Installing CompuScope Win 2000 Driv
Page 51 and 52: You will see the following window:
Page 53 and 54: Add/Remove Hardware Wizard will ask
Page 55 and 56: From the list of available Models f
Page 57 and 58: Please make sure that you write dow
Page 59 and 60: Select Memory Range and click on Ch
Page 61 and 62: Note: Follow the same procedure out
Page 63 and 64: Installing CompuScope Win NT Driver
Page 65 and 66: Click Next to continue with the ins
Page 67 and 68: Installing GageScope ® for DOS Ins
Page 69: Note: You may click the Cancel butt
Page 73 and 74: Chapter 2 - Verifying Driver Instal
Page 75 and 76: Which version of Gage Config do I h
Page 77 and 78: Checking the Status of Your Board(s
Page 79 and 80: Memory Conflict If the Board Name f
Page 81 and 82: Resolving I/O Conflicts Note: This
Page 83 and 84: How to Respecify I/O Addresses in G
Page 85 and 86: The Status Box should now read Save
Page 87 and 88: To resolve conflicts caused by memo
Page 89 and 90: To try another memory base address,
Page 91 and 92: Bus Speed Some BIOS’s allow non-s
Page 93 and 94: Detailed Description of Gage Config
Page 95 and 96: I/O Address Field Upon running Gage
Page 97 and 98: Board Name Field If your board is f
Page 99 and 100: Memory Size Field The Memory Size f
Page 101 and 102: Add Button The Add button allows yo
Page 103 and 104: Remove Button The Remove button all
Page 105 and 106: Save Button The Save button saves t
Page 107 and 108: Operation Mode Box The Operation Mo
Page 109 and 110: Configuration File Box The Configur
Page 111 and 112: Driver Version Button The Driver Ve
Page 113 and 114: The AutoVerify checkbox allows you
Page 115 and 116: If you click Add System without fir
Page 117 and 118: Save All Button The Save All button
Page 119 and 120: Close Button The Close button allow
Page 121 and 122:
Verifying Driver Installation with
Page 123 and 124:
While editing a field: or Moves
Page 125 and 126:
Setting the I/O and Memory Segment
Page 127 and 128:
Note: For CP500 boards, the final f
Page 129 and 130:
section I/O Addresses for CompuScop
Page 131 and 132:
386MAX, another popular memory mana
Page 133 and 134:
Because these CompuScope cards requ
Page 135 and 136:
Other Cards in your System Other ca
Page 137 and 138:
Chapter 3 - Verifying Signal Acquis
Page 139 and 140:
This will activate a second screen
Page 141 and 142:
Change the frequency of the signal
Page 143 and 144:
This short experiment proves that c
Page 145 and 146:
Verifying Signal Acquisition with G
Page 147 and 148:
Use the or + key to change the C
Page 149 and 150:
Chapter 4 - Uninstalling CompuScope
Page 151 and 152:
Double-click on System Devices. A w
Page 153 and 154:
2. Find and delete the .INF file th
Page 155 and 156:
Double-click on Class and the follo
Page 157 and 158:
In the right-hand portion of the wi
Page 159 and 160:
Uninstalling CompuScope Win 95/98 D
Page 161 and 162:
Click on . A window will appear ask
Page 163 and 164:
Uninstalling CompuScope Win 2000 Dr
Page 165 and 166:
You will see the following window:
Page 167 and 168:
The Add/Remove Hardware Wizard want
Page 169 and 170:
We will first make sure that all hi
Page 171 and 172:
Make sure that you select Show hidd
Page 173 and 174:
Double click on this file to open i
Page 175 and 176:
In the Window that appears, enter r
Page 177 and 178:
When you Click Permission, the foll
Page 179 and 180:
The Regedit window reappears: At th
Page 181 and 182:
Following window will appear. Type
Page 183 and 184:
Step 3B (GAGE ISA BUS CARDS ONLY) D
Page 185 and 186:
Step 3B (GAGE PCI BUS CARDS ONLY) D
Page 187 and 188:
Step 3C Double-click through the fo
Page 189 and 190:
Uninstalling GageScope ® for DOS T
Page 191 and 192:
Uninstalling CompuScope Win NT Driv
Page 193 and 194:
Chapter 5 - Files Copied in the Ins
Page 195 and 196:
Gage Products For ordering informat
show all

Driver Installation Guide - Egmont Instruments

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?