MICROMASTER 440 - Siemens AS

More documents

Recommendations

Info

4 Communications Issue 10/06 4 Communications 4.1 Establishing communications MICROMASTER 440 ⇔ STARTER The following optional components are additionally required in order to establish communications between STARTER and MICROMASTER 440: ‣ PC frequency inverter connecting set ‣ BOP if the USS standard values (refer to Section 6.4.1 "Serial Interface (USS)") are changed in the MICROMASTER 440 frequency inverter PC frequency inverter connecting set MICROMASTER 440 USS settings, refer to 6.4.1 "Serial Interface (USS)" STARTER Menu, Options --> Set PG/PC interface --> Select "PC COM-Port (USS)" --> Properties --> Interface "COM1", select a baud rate NOTE The USS parameter settings in the MICROMASTER 440 frequency inverter and the settings in STARTER must match! 4.2 Establishing communications MICROMASTER 440 ⇔ AOP ‣ Communications between AOP and MM440 are based on the USS protocol, analog to STARTER and MM440. ‣ Contrary to the BOP, the appropriate communication parameters - both for the MM440 as well as for AOP - should be set if the automatic interface detection was not carried-out (refer to Table 4-1). ‣ Using the optional components, the AOP can be connected to the communication interfaces (refer to Table 4-1). Table 4-1 MM440 parameters - baud rate - bus address AOP parameters - baud rate - bus address Options - direct connection - indirect connection AOP at the BOP link P2010[1] – P8553 – No option necessary BOP/AOP door mounting kit (6SE6400-0PM00-0AA0) AOP at the COM link P2010[0] P2011 P8553 P8552 Not possible AOP door mounting kit (6SE6400-0MD00-0AA0) MICROMASTER 440 24 Operating Instructions (Compact)
Issue 10/06 4 Communications AOP as control unit Parameter / Terminal AOP on BOP link AOP on COM link Command source Frequency setpoint (MOP) / P0700 4 5 P1000 1 P1035 2032.13 (2032.D) 2036.13 (2036.D) P1036 2032.14 (2032.E) 2036.14 (2036.E) Output frequency of the MOP higher Output frequency of the MOP lower Acknowledge fault P2104 2032.7 2036.7 • A fault can be acknowledged via the AOP independently of P0700 or P1000. 4.3 Bus interface (CB) Bus interface (CB) DeviceNet CANopen PROFIBUS P0918 P0918 P0918 *) Baud rate is automatically specified by the master P2040 P2040 P2040 P2041 P2041 P2041 P2051 P2051 P2051 *) DIP switch for addressing the hardware must be observed DeviceNet CANopen PROFIBUS P2041[0] P2041[1] PZD length Status/actual value PZD length control/setpoint P2041[2] Baud rate 0: 125 kbaud 1: 250 kbaud 2: 500 kbaud Data transfer type from T_PD0_1, T_PD0_5 Data transfer type T_PD0_6 R_PD0_1 R_PD0_5 R_PD0_6 Mapping CANopen MM4 P2041[3] Diagnostics Mapping CANopen MM4 P2041[4] _ - response to communication errors - baud rate Setting is not required (only in special cases). Refer to the Operating Instructions "PROFIBUS option module" MICROMASTER 440 Operating Instructions (Compact) 25
Page 1 and 2: MICROMASTER 440 0,12 kW - 250 kW Op
Page 3 and 4: Issue 10/06 Contents Contents 1 Ins
Page 5 and 6: Issue 10/06 1 Installation 1 Instal
Page 7 and 8: Issue 10/06 2 Electrical Installati
Page 23: Issue 10/06 3 Factory setting 3 Fac
Page 27 and 28: Issue 10/06 5 BOP / AOP (Option) 5.
Page 29 and 30: Issue 10/06 6 Commissioning P0304 =
Page 33 and 34: Issue 10/06 6 Commissioning START T
Page 35 and 36: Issue 10/06 6 Commissioning 6.4.3 D
Page 37 and 38: Issue 10/06 6 Commissioning 6.4.5 S
Page 39 and 40: Issue 10/06 6 Commissioning 6.4.7 A
Page 41 and 42: Issue 10/06 6 Commissioning 6.4.9 F
Page 43 and 44: Issue 10/06 6 Commissioning 6.4.11
Page 51 and 52: Issue 10/06 6 Commissioning 6.4.17.
Page 57 and 58: Issue 10/06 6 Commissioning P0731=5
Page 59 and 60: Issue 10/06 6 Commissioning 2 ON OF
Page 65 and 66: Issue 10/06 6 Commissioning PID can
Page 71 and 72: Issue 10/06 6 Commissioning Example
Page 73 and 74: Issue 10/06 6 Commissioning r0054 C
Page 75 and 76:
Issue 10/06 6 Commissioning 6.5 Ser
Page 77 and 78:
Issue 10/06 7 Displays and messages
show all

MICROMASTER 440 - Siemens AS

Create successful ePaper yourself

Delete template?

Save as template?