Olympus E-300 Advanced Manual

More documents

Recommendations

Info

11 Appendix Camera maintenance CLEANING MODE —Removing dust on the CCD If dust or dirt gets on the CCD, black dots may appear in the picture. If this happens, contact your <strong>Olympus</strong> Authorized Service Center to have the CCD physically cleaned. The CCD is a precision device and is easily damaged. When cleaning the CCD yourself, be sure to follow the instructions below. When cleaning the CCD, the specified AC adapter should be used (~ P. 206). If a battery is used and power runs out during cleaning, the shutter will close, which may cause the shutter curtain and mirror to break. Remove the lens from the camera. 1 Set the power switch to ON. 2 Menu T 2 T CLEANING MODE 3 ~ “How to use the menus” (P. 25) Press , then press the 4 OK button. ● The camera enters the cleaning mode. Press the shutter button fully. 5 ● The mirror goes up and the shutter curtain opens. Clean the CCD. 6 ● Carefully blow off any dust on the surface of the CCD by using a mechanical blower (commercially available). Be careful not to catch the mechanical 7 blower in the shutter curtain when turning the power off to finish cleaning. ● If the camera turns off, the shutter curtain closes, causing the mirror to fall. ● Be careful to not let the mechanical blower (commercially available) touch the CCD. If the blower touches the CCD, the CCD will be damaged. ● Never put the mechanical blower behind the lens mount. If the power turns off, the shutter closes, breaking the shutter curtain. ● Do not use anything other than the mechanical blower. If high-pressure gas is sprayed onto the CCD, it will freeze on the CCD’s surface, damaging the CCD. 182 Note 1 2 1 2 OK button PIXEL MAPPING CLEANING MODE RESET LENS OFF ERASE SETTING NO COLOR SPACE s RGB CANCEL MENU SELECT GO Shutter button
Camera maintenance PIXEL MAPPING — Checking the image processing functions The PIXEL MAPPING feature allows the camera to check and adjust the CCD and image processing functions. It is not necessary to operate this function frequently. Approximately once a year is recommended. After using the monitor or taking continuous shots, wait for at least one minute before using the PIXEL MAPPING function to ensure that it operates correctly. 1 Menu T 2 T PIXEL MAPPING ~ “How to use the menus” (P. 25) Press , then press the 2 OK button. ● The busy bar is displayed during PIXEL MAPPING. When PIXEL MAPPING is finished, the menu is restored. Note ● If you accidentally turn the camera off during PIXEL MAPPING, start again from Step 1. 1 2 1 2 PIXEL MAPPING CLEANING MODE RESET LENS OFF ERASE SETTING NO COLOR SPACE s RGB CANCEL MENU SELECT GO BUSY OK button 183 11 Appendix
Page 1 and 2:
DIGITAL CAMERA ADVANCED MANUAL Basi
Page 3 and 4:
How to read the instruction pages C
Page 5 and 6:
Contents Selecting the right mode f
Page 7 and 8:
Contents Date/time setting . . . .
Page 9 and 10:
For customers in North and South Am
Page 11 and 12:
For your safety Lightning — If a
Page 13 and 14:
For your safety � Be careful with
Page 15 and 16:
WARNING FCC Notice For your safety
Page 17 and 18:
1 Basic operations The advanced sho
Page 19 and 20:
How to use the buttons and control
Page 21 and 22:
1 2 How to use the buttons and cont
Page 23 and 24:
6 How to use the buttons and contro
Page 25 and 26:
How to use the menus The camera’s
Page 27 and 28:
3 Press to move to the functions of
Page 29 and 30:
2 Things to know before shooting Th
Page 31 and 32:
2 Press the shutter button halfway
Page 33 and 34:
Selecting the record mode You can s
Page 35 and 36:
Record mode Record mode RAW TIFF SH
Page 37 and 38:
3 Selecting the right mode for shoo
Page 39 and 40:
Selecting the right mode for the sh
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
A : Aperture priority shooting Sele
Page 47 and 48:
S : Shutter priority shooting Selec
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
4 Various shooting functions The fl
Page 55 and 56:
Flash shooting 1st curtain Usually,
Page 57 and 58:
Flash modes available in the exposu
Page 59 and 60:
Using the built-in flash Flash shoo
Page 61 and 62:
Optional electronic flashes Flash s
Page 63 and 64:
5 Select the desired flash control
Page 65 and 66:
Non-specified commercial flashes Fl
Page 67 and 68:
2 Start shooting. ● Press the shu
Page 69 and 70:
2 Press . ● The BKT selection scr
Page 71 and 72:
WB bracketing Drive mode Three imag
Page 73 and 74:
Using the self-timer 1 Press the sh
Page 75 and 76:
Drive mode TIPS The remote control
Page 77 and 78:
5 Focusing functions When you turn
Page 79 and 80:
Focus mode Three focus modes are av
Page 81 and 82:
Simultaneous use of S-AF mode and M
Page 83 and 84:
Manual focus (MF) This function all
Page 85 and 86:
6 Exposure, image and color If you
Page 87 and 88:
Metering mode—Changing the meteri
Page 89 and 90:
Example: When adjusting the exposur
Page 91 and 92:
ISO sensitivity—Setting the desir
Page 93 and 94:
White balance—Adjusting the color
Page 95 and 96:
Setting the white balance You can a
Page 97 and 98:
Setting the one-touch white balance
Page 99 and 100:
4 The color becomes bluer each time
Page 101 and 102:
SHARPNESS This function adjusts the
Page 103 and 104:
SATURATION This function sets the c
Page 105 and 106:
NOISE REDUCTION This function reduc
Page 107 and 108:
7 Playback One of the big advantage
Page 109 and 110:
Close-up playback This function let
Page 111 and 112:
Index display Viewing still images
Page 113 and 114:
Information 2 Print reservation, pr
Page 115 and 116:
Rotating images This function lets
Page 117 and 118:
Editing still images Recorded image
Page 119 and 120:
Protecting images—Preventing acci
Page 121 and 122:
All-frame erase 1 Menu T T CARD SET
Page 123 and 124:
8 Customizing the settings/function
Page 125 and 126:
CUSTOM OK This lets you select a sh
Page 127 and 128:
Date/time setting Date and time inf
Page 129 and 130:
FILE NAME When you take a picture,
Page 131 and 132: Setting the warning tone The camera
Page 133 and 134: Available modes 1 P A S M SCENE Men
Page 135 and 136: CARD SETUP — Formatting the card
Page 137 and 138: 9 Printing Turning the images you s
Page 139 and 140: Picture size and printing Print res
Page 141 and 142: Set the printing data. NO DATE TIME
Page 143 and 144: Setting printing data Print reserva
Page 145 and 146: 6 Press to select the frame with pr
Page 147 and 148: Connecting the camera to a printer
Page 149 and 150: Select frames you want to print. SE
Page 151 and 152: Setting the print paper items This
Page 153 and 154: If an error code is displayed Direc
Page 155 and 156: 10 Transferring images to a compute
Page 157 and 158: Viewing or processing images downlo
Page 159 and 160: Installing OLYMPUS Master Using the
Page 161 and 162: ● A confirmation window appears,
Page 163 and 164: Connecting the camera to a computer
Page 165 and 166: Starting OLYMPUS Master Windows 1 D
Page 167 and 168: Disconnecting the camera from your
Page 169 and 170: Printing images The print menus inc
Page 171 and 172: 11 Appendix The appendix will assis
Page 173 and 174: Lens basics Select the lens that yo
Page 175 and 176: Viewfinder indications No indicatio
Page 177 and 178: If you encounter problems Possible
Page 179 and 180: If you encounter problems Possible
Page 181: Camera maintenance Cleaning and sto
Page 185 and 186: Safety precautions ● Before going
Page 187 and 188: Glossary Compression rate Compressi
Page 189 and 190: Pixels A pixel is the smallest unit
Page 191 and 192: 12 Information This chapter covers
Page 193 and 194: Menu directory Menu Function Settin
Page 195 and 196: �Setup Menu Menu directory Menu F
Page 197 and 198: Function HQ SQ Mode P A S M � �
Page 199 and 200: Monitor ~ P. 19, 25, 108, 131 Viewf
Page 201 and 202: 4 5 6 Monitor indications (only for
Page 203 and 204: Memory gauge Battery check P 1/250
Page 205 and 206: Specifications � Exposure control
Page 207 and 208: Index (Custom) menu ...............
Page 209 and 210: MEMO 209 12 Information
Page 211 and 212: MEMO 211
show all

Olympus E-300 Advanced Manual

Create successful ePaper yourself

Delete template?

Save as template?