2 - ClamSITel
2 - ClamSITel
2 - ClamSITel
- No tags were found...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Sailplane Accessories<br />
You can install mini and micro servos in thin wings,<br />
and REMOVE them with these servo FLAT<br />
MOUNTS!<br />
RA190 Servo Flat Mounts<br />
Mini, 2 pair .................... $3.29<br />
About 1" long and 1/2" high, 2<br />
pairs per pack with 4 screws<br />
and washers. Servo Flat<br />
Mounts allow the servo to lie<br />
with its side flat against the<br />
bottom so the servo installation will take up no more depth than the actual<br />
thickness of the servo itself. In a thin wing the aileron servos need to be<br />
mounted like this. Servos can sometimes be mounted by this method inside<br />
fins and horizontal stabs. You can shorten the vertical legs to the thickness<br />
of your servo. Insert a small screw and washer into the hole in the leg to<br />
clamp the servo in place. The screw can also hold the access plate or a fairing<br />
in place on top of the servo. Fits all “mini” and “micro” servos.<br />
Control exit cover or<br />
airscoop<br />
HLH550 Exit Cover/Airscoop, 2<br />
................................................ $3.39<br />
About 2" long. White plastic. Very easy to mount — glues onto surface.<br />
Good drag reducer. Reversed, it is an airscoop for electric flight.<br />
Long, aileron pushrod<br />
fairings<br />
HLAN9321 Aileron Pushrod<br />
Fairings, pair ................ $3.89<br />
These are drag-reducing fairings<br />
for the pushrods to any control surface — ailerons, elevator, flaps,<br />
rudder, speedbrakes, spoilers. The flat base of the pushrod fairing is 5"<br />
long overall. The forward part of the base is molded with a downward<br />
bend so it won’t pull up in the airplane’s slipstream. The fairing itself is<br />
about 3-3/4" long and 5/8" high. Cut off the aft end of the Fairing to<br />
make the Fairing any length you want. One is shown cut off in the photo.<br />
The Fairings are molded of ABS plastic which can be glued or screwed<br />
down over the servo’s output arm.<br />
These aileron pushrod fairings also<br />
cover the servo.<br />
GR4269/6 Graupner<br />
Aileron Servo Covers,<br />
Pair ........................... $11.99<br />
3" long. 2" wide, 3/4" high.<br />
Use part RA190 (Servo Flat<br />
Mounts) to mount the servos in the wings. You can bolt the Aileron<br />
Servo Covers onto part RA190.<br />
Easy to install wing servo system<br />
HT0098 Wing Mount<br />
“Can” for Micro Servos, 2<br />
.................................. $8.99<br />
Clean installation for small<br />
servos in a wing or tail.<br />
Allows easy access to the<br />
servo for adjustment or<br />
repair. Made for servos of<br />
similar size to Hitec’s HS-<br />
85BB. Included are adapters to fit Airtronics, JR , Futaba.<br />
Mount your servos right next to the flight control!<br />
RA200 Surface Mount System for<br />
Standard Size Servos, Pair .......... $8.69<br />
2-3/8” square white plastic plates with<br />
molded-in exit fairings. Fasten your servo<br />
to them. When you mount the plastic plate<br />
in place you have installed your servo.<br />
Standard size servos mount in the included<br />
servo mount.<br />
RA210 Surface Mounts for Mini Servos, Pair ........................... $8.69<br />
Same as RA200 but only 2" square. For mini servos up to 1-5/8" long<br />
(to ends of mounting tabs).<br />
Sailplane Spoilers<br />
Shallow spoilers fit into THIN<br />
sailplane wings.<br />
GR104625<br />
Graupner Thin Tall<br />
Spoilers, pair<br />
.................. $49.99<br />
9-7/8" long spoilers<br />
rise to double<br />
height but are less<br />
than 1/2" deep when collapsed. These fit into thin wings, have a down<br />
lock, actuate easily and are the best spoiler we’ve seen.<br />
Graupner “Teck” Spoilers.<br />
GR931 “Teck”<br />
Spoilers for<br />
3.5M Glider,<br />
pr ......... $52.99<br />
Length: 9.85",<br />
Width; 13/32".<br />
For any 2 to<br />
3.5M sailplane. Aluminum/plastic. 1.4 oz.<br />
GR932 “Teck” Spoilers for 5M Glider, pr ........................... $59.99<br />
Length; 14.58", Width; 13/32". For any 3.5 to 5M sailplane.<br />
Aluminum/plastic. 1.9 oz.<br />
Graupner’s hinge-style glider spoilers<br />
are less than 4mm thick.<br />
GR93 Thin Spoilers,<br />
pair ............ $24.99<br />
Each spoiler assembly<br />
is 10.7" overall,<br />
1.1" wide and 3.5mm<br />
thick for easy mounting<br />
in very thin glider<br />
wings. The size of<br />
these spoilers is sufficient for sailplanes of up to 10 foot wingspan.<br />
Complete hookup accessories and instructions are provided.<br />
GR63 Control Surface Gap Tape,<br />
16 feet .................................. $38.99<br />
13/16” wide, 0.2mm thick, half of it<br />
sticks to airfoil surface. The thicker,<br />
non-stick portion stays pressed<br />
against the control surface and covers<br />
the control surface gap.<br />
Control surface Gap cover<br />
We’re open 24/7 at<br />
www.hobby-lobby.com<br />
www.hobby-lobby.com • Order Online 24/7 103