2 - ClamSITel
2 - ClamSITel
2 - ClamSITel
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Brushless Motors & Controllers<br />
Little motor - BIG power<br />
GR6531 Graupner Inline 400 8.4V Brushless Motor ................... $97.99<br />
20mm diameter, 40mm case, 10mm<br />
free shaft length, 2.3mm shaft diameter,<br />
weighs 65g, Kv of 3060 RPM/Volt.<br />
Has two mounting holes that are<br />
16mm apart with M2.5 threads. Small<br />
2-pole motor for use in the Graupner<br />
Nemesis (GR9554) with a 4.75x4<br />
CAM prop. Also suitable for use in<br />
mini hydroplane boats that use 31mm props. Best with 2 cell Lipo and 12 amp<br />
controller.<br />
OUTRUNNER motor for use in Ducted Fan<br />
MT2235 SFM OUTRUNNER Brushless Motor ....................... $39.99<br />
25.3mm (1") diameter, 31mm (1-1/4")<br />
long, 2.3mm shaft, 9 pole motor with a<br />
Kv of 3500. Motor mounts with 4-3mm<br />
screws on 16mm diameter spacing.<br />
Powerful high torque motor for use in<br />
our 66mm ducted fan (MT1028). Use<br />
with 3 cell LiPo battery and 18A Jeti<br />
Brushless controller.<br />
For 3D aerobatic models to 9-1/2 oz.,<br />
airplanes to 16 oz.<br />
SK400XT Esskay OUTRUNNER Motor,<br />
400XT ........................................... $29.99<br />
1" diameter, 1" long without shaft, 3mm<br />
shaft, weighs 1-1/2 oz. Comes complete<br />
with radial mounting adapter for mounting<br />
in front of a firewall. Attach the motor to<br />
the Jeti speed control using our 1.8mm<br />
gold connectors MJ21011, or wire directly.<br />
Use MJ4698 3mm Ultralight collet prop<br />
adapter. For lightweight 3D models to 9-<br />
1/2 oz. and other airplanes to 16 oz. Use<br />
9x3.8 to 11x3.8 prop and 2-3 LiPo cells<br />
and an 8 amp controller. Good to 10 amps<br />
but draws only 3 amps in hovering a<br />
model of 8-1/2 oz.<br />
Powerful high RPM<br />
brushless<br />
inrunner<br />
for ducted fans<br />
SFM4700 SFM 20mm Kv 4700<br />
Brushless Motor ........... $59.99<br />
20mm diameter, 40mm long,<br />
2.3mm shaft, Kv=4700, 20 amps<br />
maximum sustained current. Use in ducted fans of 50-59mm size. When<br />
used in our 56mm "XF-Fan (ETH550), powered with a 3 cell Lipo, the<br />
motor draws about 19 amps.<br />
NEW! 490 Watt EDF Motor for 4-cells<br />
FWF90137 Outrunner Brushless Motor 3500Kv for EDF….... $39.99<br />
28mm diameter, 63mm long (excluding<br />
10mm shaft), 3mm shaft, 3.1 oz,<br />
3500 Kv. Motor comes pre-connected<br />
with 3.5mm male connectors. Design<br />
has cooling holes at the front and a<br />
ventilated aerodynamic rear section<br />
for good cooling and drag reduction.<br />
Fits our 64mm fan (FWF90210) and<br />
will produce more than 2.2 pounds of<br />
thrust when mated to a 4-cell lipo battery<br />
and a 45A controller. Actual current<br />
draw is about 33A on 4-cells. Front mount is 20mm dia. with 4<br />
mounting holes on 16mm centers. Requires 4-2.5mm screws (not<br />
included). Rear mounting ring is about 24mm dia. and stabilizes the<br />
motor inside the fan. The main part of the fan remains in the cooling<br />
air stream.<br />
With full 2 year warranty<br />
Proportional Motor Controls for<br />
Brushless Motors<br />
Jeti ECO: low cost<br />
brushless motor controllers are<br />
the easiest to use<br />
Jeti's ECO line of brushless<br />
controllers with BEC (battery<br />
eliminator circuit) offers the<br />
sport modeler a low cost<br />
choice in high quality controllers.<br />
Controllers "autodetect"<br />
the number of poles in<br />
the motor and pick the optimal timing. The settings have been reduced<br />
to four modes simply selected by jumper, no programming required.<br />
Controllers "auto-detect" full throttle position. Each unit can run up to 4<br />
servos when used with up to 3 lithium cells. Controllers have temperature<br />
overload protection and will cut the power to the motor if controller<br />
reaches 100-110 degrees C. All Jeti controllers come with a 2-year free<br />
replacement warranty!<br />
Mode 1: NiCad/NiMH – Brake Off. Non-active brake with slow down<br />
type low voltage cut-off down to 5 volts or 0.7 volts per cell.<br />
Mode 2: NiCad/NiMH – Brake On. Active brake with hard type low voltage<br />
cut-off at 5 volts or 0.7 volts per cell.<br />
Mode 3: LiIon/LiPoly – Brake Off. Non-active brake with slow down<br />
type low voltage cut-off. Minimum voltage 6 volts for 2 cell packs, 9<br />
volts for 3 cell packs.<br />
Mode 4: LiIon/LiPoly – Brake On. Active brake with hard type low voltage<br />
cut-off. Minimum voltage 6 volts for 2 cell packs, 9 volts for 3 cell<br />
packs.<br />
For 2-3 Li cells,<br />
to 8 Amps<br />
JEE008 Jeti "ECO 8" 8 Amp<br />
Controller for<br />
Brushless Motor .......... $39.99<br />
1" x 5/8" x 3/16", 7 grams (1/4<br />
oz.), 8 Amps continuous, for 2 to 3 Lithium cells. BEC can run a maximum<br />
of 4 servos. The brake can be turned on and off using your transmitter.<br />
The low voltage cutoff is set for 3V per cell.<br />
For 6-10 Ni, 2 to 3 Li cells, to 12 Amps<br />
JEE012 Jeti "ECO 12" 12 Amp Controller<br />
for Brushless Motor ......................... $43.99<br />
1-3/4" x 1" x 1/4", 10 grams (1/3 oz.) 12 amps<br />
continuous, for use with 6-10 NiCad or NiMH,<br />
2-3 Lithium cells. BEC can run 4 servos with<br />
up to 3 Lithium cells, or 3 servos if 10<br />
NiCad/NiMH are used.<br />
For 6-10 Ni, 2 to 3 Li cells, to 18 Amps<br />
JEE018 Jeti "ECO 18" 18 Amp Controller<br />
for Brushless Motor ........................... $47.99<br />
1-3/4" x 1" x 5/16", 21 grams (3/4 oz.) 18 amps<br />
continuous, for use with 6-10 NiCad or NiMH,<br />
2-3 Lithium cells. BEC can run 4 servos with<br />
up to 3 Lithium cells, or 3 servos if 10<br />
NiCad/NiMH are used.<br />
For 6-10 Ni, 2 to 3 Li cells, to 25<br />
Amps<br />
JEE025 Jeti "ECO 25" 25 Amp Controller for<br />
Brushless Motor ................................. $52.99<br />
1-3/4" x 1" x 7/16", 28 grams (1 oz.) 25 amps<br />
continuous, for use with 6-10 NiCad or NiMH, 2-3 Lithium cells. BEC<br />
can run 5 servos on 4-6 NiCad/NiMH cells or 2 Lithium, 4 servos with<br />
7-8 NiCad/NiMH cells or 3 Lithium, or 3 servos if 10 NiCad/NiMH are<br />
used.<br />
68<br />
Your R/C Superstore • (866) 512-1444