2 - ClamSITel
2 - ClamSITel
2 - ClamSITel
- No tags were found...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Adhesives<br />
GR959 Graupner "Uhu Por" Glue<br />
for Styrofoam .............. $7.89<br />
1.4 oz. tube (40 grams). Does not<br />
melt foam. Works primarily as a<br />
contact glue, apply thin layer to<br />
both mating surfaces, allow to set<br />
for 10 minutes, then press together. Make sure you are correctly<br />
aligned before touching pre-glued parts together, part will be difficult to<br />
re-position. Will glue anything to foam or foam to itself. Dries fast.<br />
Superior<br />
Super-Glue!<br />
ZAP009 Zap CA Thin<br />
Viscosity, 1/2 oz ............ $4.19<br />
Instant bonding.<br />
ZAP003 Zap A Gap CA+ Med.<br />
Viscosity, 1/2 oz. .......... $4.19<br />
30 second bonding, fills gaps.<br />
ZAP025 Zap-O Odorless, Foam Safe CA, 20 gr. .......... $9.99<br />
For gluing foam. Slow bonding.<br />
ZAP015 Zap Kicker, 2 oz. Spray .................................... $5.99<br />
Makes slower curing CA glues set instantly.<br />
ZAP016 Z-7 Debonder, 1 oz. .......................................... $4.09<br />
For releasing CA glue joints.<br />
ZAP018 Z-Ends and Teflon Tubing, 10 ......................... $3.79<br />
ZAP020 Zap "Slo-Zap" High Viscosity CA, 1 oz. .......... $7.59<br />
Thick, slow bonding CA glue, fills gaps.<br />
ZAP026 "Zap Gel" Adhesive/Sealer, .7 oz. .................... $7.99<br />
Thickest and strongest CA glue available.<br />
Devcon Epoxy Glues,<br />
Thread lock<br />
DEV205 5 Minute Epoxy, 1 oz. .................................................. $4.39<br />
DEV206 5 Minute Epoxy, 2.5 oz. ............................................... $7.59<br />
DEV209 5 Minute Epoxy, 9 oz. ................................................ $17.39<br />
DEV233 30 Minute Epoxy, 9 oz. .............................................. $16.09<br />
DEV235 30 Minute Epoxy, .8 oz. ............................................... $4.69<br />
DEV360 Thread Lock, .2 oz. ...................................................... $3.59<br />
A. “Airplane Glue” - it’s very fast setting and<br />
glues ABS plastic!<br />
GR9534 UHU-Hart, 1 oz. ............................................................ $4.89<br />
GR9535 UHU-Hart, 4 oz. ............................................................ $9.99<br />
Absolutely clear, ultra lightweight and strong when dried. This is the best<br />
selling model airplane cement in Germany. It dries so fast on balsa<br />
joints its almost like using CA. It is extremely strong and light. It slightly<br />
melts ABS plastic so it makes both a glue bond and a “weld” on ABS<br />
parts like boat hulls and airplane plastic fuselages.<br />
B. Stabilit Express-you’ll become addicted to it!<br />
GR9601 Pattex Stabilit Express, 1 oz. .................................... $14.99<br />
GR9602 Pattex Stabilit Express, 3 oz. .................................... $28.99<br />
As an adhesive Stabilit Express will firmly adhere anything to anything<br />
else. It is unsurpassed for joining such critical things as a nylon bellcrank<br />
to a fiberglass fuselage, or metal or plastic tubes to plastic or fiberglass.<br />
It is a two part methylacrylic adhesive. The material sets in only<br />
20 minutes into a wood-colored mass. The fully cured material can be<br />
sanded and finished. The cured material has both compression and tensile<br />
strength, so it can be used as a structural element in addition to simply<br />
bonding other structures.<br />
PFM glues anything to anything!<br />
HLIMP001 “P.F.M” Adhesive-Sealant, 3.7 oz. ........................ $13.99<br />
PFM is a one part, quick setting adhesive and sealant that glues just<br />
about anything to anything else. It will melt foam however. It sets in<br />
about 30 minutes. PFM sets but doesn't get brittle; it will give without<br />
letting go. PFM is non-flammable.<br />
PFM can repair electrical insulation, give strain relief to electric connectors,<br />
glue servos in place, glue servo trays and bulkheads in fiberglass<br />
fuselages. PFM is the indispensable glue in your workshop,<br />
thousands of uses and counting.<br />
Glue ABS to ABS or<br />
to wood<br />
KK80478 Krick<br />
Special Adhesive<br />
for ABS ................... $5.99<br />
Inexpensive main<br />
landing gears<br />
RA1093 13” Main Landing Gear ............................................... $9.99<br />
RA1094 16” Main Landing Gear ............................................... $9.99<br />
Small one is about 2” high, large one about 4”. Can be bent for more height<br />
and narrower tread.<br />
Strong lightweight retracts for airplanes<br />
up to 2 pounds<br />
ALF6001 Alfa Model Retractable<br />
Undercarriage Set ................... $26.99<br />
The most versatile and strongest landing<br />
gear set for light airplanes that we have<br />
ever seen. Injection molded reinforced<br />
plastic with 3mm carbon legs and 2mm<br />
steel hinge pins and axles, mounting<br />
screws are included. Base is approx.<br />
5/8" W x 1-7/16" L x 7/16" H. Gear length can<br />
be up to 5" from hinge pin to center of wheel.<br />
Can be assembled in a couple of minutes. 90<br />
degree or 85 degree operation to match wing<br />
dihedral. A pair of retracts can be operated by a<br />
single micro servo (HS-55) mounted in the fuselage.<br />
These either "retract inward" or "retract<br />
outward". In both cases the servo remains in<br />
the fuselage. A pair of retracts can be used in tandem for planes like<br />
the Alfa Beaufighter or Flying Styro Mosquito. Additional parts in the kit<br />
allow you to adjust the gear offset and even to add scale, springloaded<br />
movement. The sprung "knuckle style" axle assembly has nearly<br />
5/8" of movement and absorbs harsh landing loads. Clear instructions<br />
with exploded view drawings and dimensions.<br />
ALF60011 Alfa Model Retract<br />
Mechanism, pair ........................... $19.99<br />
Includes the mechanical parts, 3mm carbon<br />
gear legs, 2mm steel hinge pins and axles.<br />
Works as either a 90 or 85 degree retract.<br />
Does not include the parts for the spring<br />
loaded "knuckle style" axle assembly or the<br />
"break-away" function.<br />
ALF60012 Alfa Model Knuckle Axle<br />
Assembly .................................. $10.99<br />
Parts for spring loaded axle assembly.<br />
Can be adapted to the landing gear on<br />
any airplane up to 2 pounds. Fits a 3mm<br />
gear leg (not included). Reduces the<br />
shock transmitted into the airframe due to<br />
stiff landing gear.<br />
90<br />
Cyanoacrylate glue for foam models<br />
KF022 Foam Safe CA Glue, 1 oz. ........................... $10.99<br />
Low odor, fills gaps well, dries in about a minute.<br />
KF023 Accelerator, 2 oz. Pump Spray ..................... $5.99<br />
Foam friendly accelerator; use sparingly to set CA instantly.<br />
The name says it all!<br />
RA1072 Shock Absorbing Universal<br />
Steerable Nose Gear ................. $12.99<br />
5/32" (4mm) wire. 8-1/4" overall length. This is everything the name<br />
says it is: It absorbs up and down jolts with its tempered steel springs,<br />
it mounts in any .30 to .90 size airplane, it is steerable, and it comes<br />
assembled. Nose gear travels up and down on brass bushings.<br />
Your R/C Superstore • (866) 512-1444