2 - ClamSITel

FULL 2-YEAR WARRANTY
Fully programmable brushless
motor controllers
Atlas motor controllers will work with all types of brushless motors.
Atlas controllers come pre-programmed and are ready to use when
you receive them. Additional controller adjustments are available; most
can be accessed and adjusted with your transmitter, but for easier programming,
use the included program card to set all your options. This
only takes a few seconds. Settings can easily be changed at the flying
field without the need for additional instructions or a computer.
Atlas Black Opto Controllers
When you need more than 3 Lithium cells in your flight pack it is necessary
to use an "Opto" controller. Opto controllers do not have a BEC
(battery eliminator circuit) to power your radio receiver and servos. An
alternate power supply is necessary. Use either a standard 4.8V
receiver battery pack or a UBEC (KFS001 - KFS003). A UBEC is a
device that reduces the high voltage of your flight batteries and supplies
regulated power suitable to run your receiver and servos.
Every Atlas programmable brushless motor controller has:
A 2-Year Warranty
A FREE Programming Card
Over-temperature protection
Works with any brushless motor
Can be used in airplanes or helicopters (has governor mode)
An easy to use programming guide
Every Atlas controller can be programmed for:
NiCd, NiMH or Lithium Batteries (Type and number of cells)
Hard or Soft Start
Motor Timing:
Auto Detect
Soft "Inrunners" (0 to 7 degrees)
Hard "Outrunners" (22 to 30 degrees)
Brake: On/Off
Motor Rotation:
Normal
Reverse
Low Voltage Cut Off:
Ignore
Reduce Power
Hard Cut Off
Governor Mode (Helicopter use)
ABC08 Atlas 8 Amp
Brushless Controller ................... $29.99
1-3/8" x 7/8" x 3/8", 11 grams (1/3 oz.). 8
Amps continuous, for 5 to10 NiCd or
NiMH, 2 to 3 Lithium cells. BEC can run 4
servos on 6 cell battery, 2 servos on 10
cells. Order connector set MJ21011.
ABC12 Atlas 12 Amp
Brushless Controller ..................... $34.99
1-3/8" x 7/8" x 3/8",11 grams (1/3 oz.). 12
Amps continuous, for 5 to 10 NiCd or NiMH,
2 to 3 Lithium cells. BEC can run 4 servos
on 6 cell battery, 2 servos on 10 cells.
Order connector set MJ21011.
ABC20 Atlas 20 Amp
Brushless Controller ...................... $38.99
1-7/8" x 7/8" x 3/8", 19 grams (5/8 oz.). 20
Amps continuous, for 5 to 10 NiCd or NiMH,
2 to 3 Lithium cells. BEC can run 4 servos
on 6 cell battery, 2 servos on 10 cells. Order
connector set MJ21011.
ABC35 Atlas 35 Amp
Brushless Controller ..................... $56.99
1-7/8" x 15/16" x 1/2", 31 grams (1-1/8 oz.).
35 Amps continuous, for 5 to 10 NiCd or
NiMH, 2 to 3 Lithium cells. BEC can run 4
servos on 6 cell battery, 3 servos on 10
cells. Connectors included.
ABC45 Atlas 45 Amp
Brushless Controller ... $67.99
3-1/8" x 1-1/16" x 3/8", 39 grams
(1-1/3 oz.). 45 Amps continuous,
for 5 to 10 NiCd or NiMH, 2 to 3
Lithium cells. BEC can run 5 servos
on 6 cell battery, 3 servos on 10
cells. Connectors included.
ABC75 Atlas 75 Amp
Brushless Controller ............ $99.99
3-1/8" x 1-1/16" x 3/8", 50 grams (1-3/4
oz.). 75 Amps continuous, for 5 to 10
NiCd or NiMH, 2 to 3 Lithium cells. BEC
can run 5 servos on 6 cell battery, 3
servos on 10 cells. Connectors included.
ABC45P Atlas 45 Amp Opto
Brushless Controller ............ $67.99
3-1/8" x 1-1/16" x 3/8", 34 grams (1-1/5
oz.). 45 Amps continuous, for 6 to 16
NiCd or NiMH, 2 to 5 Lithium cells,
Connectors included. No BEC.
ABC75P Atlas 75 Amp Opto
Brushless Controller ........ $99.99
3-1/8" x 1-1/16" x 3/8", 46 grams (1-
5/8 oz.). 75 Amps continuous, for 6 to
16 NiCd or NiMH, 2 to 5 Lithium cells,
Connectors included. No BEC.
ABC90P Atlas 90 Amp Opto
Brushless Controller ................. $199.99
2-5/8" x 2-1/16" x 11/16", 115 grams (4 oz.),
90 Amps continuous, for 16-30 NiCd or
NiMH, 5-10 Lithium cells. Use with large
OUTRUNNER motors in demanding applications.
Solid screw-in-place installation, 3 rubber
grommet shock mounts. 2.5mm silicone
insulated wire on motor leads, 3mm silicone
insulated wire on battery leads. 13" long wire to receiver. Connectors
included. No BEC.
Large 2" x 2" x 5/16" aluminum heat sink
dissipates excess heat to keep the controller
in a safe operating temperature
range.
ABC01 Spare Atlas Programming Card
8-75 Amp ............................................... $4.99
1-1/4" x 1-7/8" x 1/16" card with jumper connectors
programs the 8A to 75A Atlas controllers.
Pick the program options that you want by moving
the jumpers to the appropriate pins on the card, plug your Atlas
controller into the Program Card, switch on the controller for a few seconds
and your settings have been programmed; a "Beep" tone verifies
the process. A 4.8V receiver battery is required to program the Opto
controllers. Changes take only seconds to perform; no other support
equipment or computer is required.
With the Programming card you can select:
NiCd and NiMH or Lithium battery (Type and cell count)
Hard or Soft Start
Hard or Soft Cutoff
Timing: Low for Inrunners, High for OUTRUNNERS,
or Auto Detect
Brake On or Off
Direction of Rotation of Motor
Governor Mode for Helicopters
ABC02 Spare Atlas Programming Card 90 Amp .................... $4.99
1-1/4" x 1-7/8" x 1/16" card with jumper connectors programs the 90A
Atlas controllers. Same functions as ABC01 with the addition of settings
for up to 10 cell lithium batteries that the 90A controller is able to
use.
www.hobby-lobby.com • Order Online 24/7 67