2 - ClamSITel

More documents

Recommendations

Info

GR6317 Speed 700 BB Turbo, 12V …........................................................ $44.99 Direct Drive for planes to 60 oz., sailplanes to 100 oz.: 372 Watts, 14.4 Volts, 5,900 rpm, 12x8 prop, 25 Amps, 35 oz. thrust. Geared for planes to 100 oz., sailplanes to 150 oz.: 496 Watts, 19.2 Volts, 2:1 gear ratio, 16x8 prop, 25 Amps, 55 oz. thrust. Proportional Motor Controls for Motors with Brushes Jeti Controllers for Brush motors -- for flyers who hate reading operating manuals Jeti brings you more control options but fewer directions for you to follow. You can program each of these controllers to follow one of 4 operating conditions by simply changing the location of a little jumper connector on the controller. The 4 operating conditions are: 1. Propeller Brake ON, Battery type NiCd or NiMh, Motor cut-off at 4 Volts (or 0.7V per cell) 2. Prop Brake OFF, Battery type NiCd or NiMh, gradual Motor cutoff at 4 Volts (or 0.7V per cell) 3. Prop Brake ON, Battery type Li-polymer, gradual Motor cut-off at minimum voltage 5.2V with 2 Li cells, and 9V with 3 Li cells 4. Prop Brake OFF, Battery type Li-polymer, gradual Motor cut-off at minimum voltage 5.2V with 2 Li cells, and 9V with 3 Li cells These controllers all have: high rate variable switching (1000-4000 Hz), with high output BEC (Battery Eliminator Circuit: powers receiver and servos from the big motor battery) that allows a lot of servos to operate, user-programmable settings as listed above, automatic adjustment of the throttle range, safe “power on” arming (keeps motor from starting when not expected), “soft start up” to prevent propeller or gearbox damage, automatic shut down when signal is lost, and limited maximum braking action to prevent prop or gear damage. They also have automatic current limiting that will allow the current to your motor to exceed the normal level by about 5 Amps before cutting off. For 4 to 8 Ni, 2 to 3 Li cells, 6 to 8 Amps JES006 Jeti 6 Amp Microprocessor ....... $23.99 0.7”x0.6”x0.2”, 0.2 oz. Brushed and BEC’s For electric heli’s, 6-12 cells, no motor cutoff JE300HE Jeti 30 Helicopter Microprocessor ........................................ $43.99 For 6-12 cells, 30 Amps continuous current, BEC for recvr. and up to 3 servos, no motor cutoff in BEC to avoid sudden landings when battery goes down, has current limiter protection that stops motor if it is blocked, no prop brake, 1000hz. switching frequency, adjustable pot for motor start point, 1 oz., 43x22x10mm. Self adjusts to transmitter motor start point, gives more linear throttle response. JE450 Jeti 45 Microprocessor ........... $52.99 For 8 to 30 cells, 45 Amps continuous current and 60 Amps for up to 30 seconds. No BEC. 8 to 30 cell controller for up to 60 Amps JE60 Jeti 60 ........................................... $77.99 For 8-30 cells, 60 Amps continuous current, no BEC, has current limiter protection that stops motor if it is blocked, on/off brake, adjustable pot for motor start point, LED for brake set, off, and max power, 2400hz. switching frequency, 1-3/8 oz., 51x30x10mm. “Add-on” BEC NEW! Reliable power to your receiver and servos JE512 Jeti MAX BEC, 5.5-16V Input, 5-6V 10A Output .... $49.99 MAX BEC is a linear regulator designed to supply consistent power to the radio system and servos in a model aircraft. Either Nicad/NiMH or Lipoly/LiIon cells supply input voltage, 2 Lithium cells are recommended. MAX BEC includes a charging connector, batteries can be charged in place if desired. Output voltage of 5V or 6V can be chosen by jumper connection. Two leads connect the BEC to your receiver this provides redundancy and reduces the amp load on each connection. The connectors can be plugged into any channel on your receiver. The BEC includes a “safe” switch; in the event of mechanical damage or switch failure the system fails in the ON position and has no impact on the BEC operation. For 4 to 8 Ni, 2 to 3 Li cells, 12 to 15 Amps JES012 Jeti 12 Amp Microprocessor ...... $33.99 1”x0.75”x0.3”, 0.53 oz. For 4-8 Ni, 2 to 3 Li cells, 20 to 22 Amps JES020 Jeti 20 Amp Microprocessor ....... $37.99 1”x0.75”x0.3”, 0.53 oz. For 6-12 Ni, 2 to 4 Li cells, 30 to 35 Amps JES030 Jeti 30 Amp Microprocessor .... $43.99 1.3”x1”x0.3”, 1 oz. NEW! Safe power to your receiver and servos, 20A output, dual redundancy JEM02 Jeti MAX BEC 2 ................................................ $99.99 MAX BEC is designed to power the receiver and servos in the model. MAX BEC is a linear voltage stabilizer with an adjustable output voltage. The output voltage is set using a jumper and in one of four positions: 5.0V, 5.4V, 5.7V or 6.0V. MAX BEC can be powered using NiXX and Li–XX cells. MAX BEC also gives an indication of used capacity of the battery with four LEDs. Part of MAX BEC is an electronic switch, which uses a highly efficient type of MOSFET transistor. The main benefits of the MAX BEC include a high voltage rating (to 12 cells NiXX) and low current in the off state (170 mA). The analog voltage stabilization does not contribute to radio interference. BEC for large electric models ABB450 Atlas Switch Mode BEC, 8-42V ......................................................... $29.99 78 For 6 -12 Ni, 2 to 4 Li cells, 45 to 50 Amps JES045 Jeti 45 Amp Microprocessor ...... $61.99 1.3”x1”x0.3”, 1 oz. 2-3/8" x 1" x 7/16", 23 grams. Input voltage range from 8 to 42 volts will work with 3 to 10 cell lithium battery packs. Output is 4 amps continuous with a peak of 5 amps. Output voltage is selectable for 5 or 6 volts by a jumper plug. Power the receiver in your aircraft and up to 10 servos from your flight batteries. Eliminates the extra weight of a separate battery pack for your radio and servos. Use with any "Opto" controller or a regular BEC equipped controller by disabling its BEC function. Your R/C Superstore • (866) 512-1444
Charging Lithium Polymer batteries just got safer LS100 "LipoSack" Fire Retardant Lipo Charging Bag ............................................................. $23.99 9" wide and 12" long, weighs 4 oz. LipoSack will allow you to charge most Lithium Polymer packs and reduce the effects of a Lithium Polymer battery charging mishap. Place LipoSack on a non-flammable surface during charging process. Route charging leads through vent at the top seam of the LipoSack. Close top flap of LipoSack and press hook and loop closure. Charge your battery using proper charging practices. Always monitor your charging batteries and never leave them unattended. It is always recommended that you charge your batteries in a well ventilated area away from flammables and children. Electric Test Equipment Measure your electric drive performance AST101 Astroflight Super Whatt Meter ............................................................ $54.99 4”x 2”x 7/8”. Measures your motor’s and battery’s Volts (to 60V), Amps (to 70A), Watts (up to 5,000), and NiCad Amp-hour Capacity (up to 9Ah). Plug in Whatt Meter between your NiCad and motor controller to measure your system’s performance. Easy to use: all information is displayed on the screen. No switches, knobs or user input required. It has two Astro connectors which you can use or replace with others. Specialized Electric Motor Mounts Electric motor mounting plates Fiberglass Motor Mounts for Electric motors: HLSIA503 1-1/8” dia., for Speed 400 ............................................... $5.99 HLSIA511 1-9/16” dia., for Speed 500/540/600 .................................. $8.99 HLSIA546 1-3/4” dia, for Speed 700 ............................................... $8.99 HLSIA520 1-3/4” dia. for Mega, Ultra, 3 holes .................................. $8.99 HLSIA538 1-15/16” dia., for Mega, Ultra, 3 holes ............................. $8.99 Glue these into fiberglass fuselages with thick CA or Stabilit Express. Perfect fit on the motors and their mounting screws. Rock solid mounts for large OUTRUNNER motors AMM400 Atlas Mount for .40-.60 Size OUTRUNNERS .......................................... $18.99 Adjustable from about 3-3/4" to 5-1/4" from firewall to front of mount. Fits AXI 41 series motors and others with the same mount spacing. AMM500 Atlas Mount for .60-1.20 Size OUTRUNNERS ................ $22.99 Adjustable from about 4-1/4" to 6" from firewall to front of mount. Fits AXI 41 and 53 series motors and others with the same mount spacing. Heavy-duty anodized aluminum motor mounts provide rock solid support for your large OUTRUN- NER motors. Each comes with screws and nuts to assemble the adjustable mount, and blind nuts and bolts for attaching mount to your firewall. The easiest way to convert your larger, glow powered airplane to OUTRUNNER power. Sturdy mount for the large AXI motors PM41001 Aluminum Motor Mount for AXI 28 and AXI 41 Series Motors ......................................... $21.99 Three piece anodized aluminum mount, adjustable for length 3-1/4” to 3-3/4”, height 2”, width 2-1/2”. Front plate pre-drilled for the 28 and 41 series AXI motors. Lightweight yet strong comes with screws and nuts for attaching the front mount to the sides. Requires 4 bolts to attach to your firewall. Electric Accessories Universal mounting system for .40-.90 size Glow to Electric conversions AMM111 Aluminum Motor Mount System for OUTRUNNERS, 40pc. ................................... $17.99 Mounts all OUTRUNNER motors that have a radial mount, to the firewall of your airplane. The aluminum spacers are about 1/2" diameter with a 5/32" hole for the long bolts. The 40 piece package includes 4 pieces each of: 3/16", 3/8", 1/2", 3/4", and 1" long spacers, and 1", 1- 9/16", 2" and 3-1/8" long 4mm hex head screws and 4mm blind nuts. The maximum length of the Motor Mount is 2-7/8". Hardware to mount an OUTRUNNER motor Tube Nylon Spacers, 1/2” diameter HLH8852 1/8” Long Spacer, 4 pcs. .......................................... $1.00 HLH8853 1/4” Long Spacer, 4 pcs. .......................................... $1.00 HLH8854 1/2” Long Spacer, 4 pcs. .......................................... $1.10 HLH8855 1” Long Spacer, 4 pcs. ............................................. $1.40 Stainless Steel Machine Screws HLH8875 3”, 8-32 Phillips Roundhead Machine Screw, 4 pcs. .............................................................................. $2.50 HLH8876 4”, 8-32 Phillips Roundhead Machine Screw, 4 pcs. .............................................................................. $4.50 Nuts and Washers HLH8860 8-32 Blind Nuts, Zinc Plated Steel, 4 pcs. .............. $1.00 HLH8861 8-32 Nyloc Nuts, Stainless Steel, 4 pcs. ................. $1.00 HLH8862 Stainless Steel Washer, 4 pcs. ................................. $0.30 Stick motor mount for AXI and Atlas OUTRUNNERS AMM010 10mm Stick Mount for OUTRUNNER Motors ............. $6.99 Weighs less than 5 grams. Includes 4 screws for mounting the motor. Machined aluminum motor mount for AXI 22 and Atlas 23 series motors (or other motor with Speed 400/480 mount spacing, 16mm/19mm). Can be screwed to the 10mm stick that is included with many models, avoiding the need for a radial mount. Can be mounted in either a pusher or tractor orientation. Horizontal mounts for 400, 500, 600 motors HLAN2096 Horizontal Mount for 400 motors ............................... $7.99 HLAN2097 Horizontal Mount for 500, 600 motors ....................... $8.99 Electric Flight Computer Program ElectriCalc for Windows! Shows you how your motor, batteries, gearbox, and prop will fly your electric airplane! ECALC2 ElectriCalc Program, Version 2.2, for Windows ............ $34.99 An easy to use program with Windows display on your pc. Enter the size and weight of your airplane. Pick a motor from Ecalc’s data base or add your own motor specs, select the number and type of cells, add a gearbox if you want, then a propeller. SEE instantly how well the combination will FLY! Change any value and SEE the results of the change in the performance figures. Thrust, rate of climb, current flow (will your 30 Amp motor controller be adequate), airspeed, efficiency, time of the motor run. Reduce the “throttle” setting to see how much power you can save. Ecalc is the answer to an electric flyer’s questions. Program comes on a CD and works with Windows 95 or later operating systems. www.hobby-lobby.com • Order Online 24/7 79
Page 2 and 3:
FlyCam/Pilot-1 Beginners/Parkflyers
Page 4 and 5:
AA1130 Acme "FlyCamOne2" Micro Vide
Page 6 and 7:
The Golden Age of Aviation produced
Page 8 and 9:
Classic Civilian aircraft from Pilo
Page 10 and 11:
Golden Age biplane - Great looks, e
Page 12 and 13:
Beginners/Parkflyers Terrific begin
Page 14 and 15:
Beginners/Parkflyers Beginner's dre
Page 16 and 17:
Flies like a Giant with only 35" Wi
Page 18 and 19:
TELEMASTER The world’s best glow
Page 20 and 21:
HLA007RW Hobby-Lobby Ready Built Se
Page 22 and 23:
TELEMASTER HUGE, Ready-Built versio
Page 24 and 25:
Warbirds ALF217 P-47 Thunderbolt AR
Page 26 and 27:
Scale Electric Flight Big 4-foot wi
Page 28 and 29: Electric Ducted Fan NEW! World’s
Page 30 and 31: Electric Ducted Fan Ducted fan JETS
Page 32 and 33: Electric Ducted Fan NEW! Navy delta
Page 34 and 35: Electric Ducted Fan Exceptionally w
Page 36 and 37: Aerobatic and 3D Flight Light and t
Page 38 and 39: Semi scale T-28 Trojan flies as goo
Page 40 and 41: Glow/Glow Conversion Big…powerful
Page 42 and 43: Micro Pylon Racers Pylon racer is q
Page 44 and 45: Sailplane Beautiful "Full-House" mo
Page 46 and 47: E-flite Helicopters An Ultra-Micro
Page 48 and 49: GAUI Advanced Helicopters NEW! 3D P
Page 50 and 51: GAUI Advanced Helicopters NEW! Ligh
Page 52 and 53: Entry level price with Spektrum’s
Page 54 and 55: SpektrumRadios and Accessories Fast
Page 56 and 57: Servos NEW! Hitec digital servos fo
Page 58 and 59: Model Motors has the most complete
Page 60 and 61: For SPEED 480/500 size airplanes, b
Page 62 and 63: More powerful motor replacement for
Page 64 and 65: Fly 20 plus pound airplanes better
Page 66 and 67: Premium OUTRUNNER Brushless motors
Page 68 and 69: Brushless Motors & Controllers Litt
Page 70 and 71: Proportional Motor Controls NEW! Ea
Page 72 and 73: Lithium Polymer Battery Packs Why c
Page 74 and 75: Lithium Polymer Battery Packs Why c
Page 76 and 77: 76 Electric Accessories LiPo Cell V
Page 80 and 81: 80 To 35 Amps: Powerpole Connectors
Page 82 and 83: 82 Ducted Fans 55mm Ducted fan for
Page 84 and 85: Electric Flight Accessories Prop ad
Page 86 and 87: 86 CAM Folding Props with Precision
Page 88 and 89: 88 Graupner “Super Nylon” Props
Page 90 and 91: Adhesives GR959 Graupner "Uhu Por"
Page 92 and 93: 92 Long Extensions for aileron serv
Page 94 and 95: 94 Airborne Tricks Thick smoke trai
Page 96 and 97: Tiny hardware for Slow and Park Fly
Page 98 and 99: 98 Slotted Cheese A Head Machine Sc
Page 100 and 101: 100 It's always bothered us to have
Page 102 and 103: Sailplane Hi-Starts The world’s f
Page 104 and 105: Low-Temperature POLYCOVER This exce
Page 106 and 107: Boats NEW! Slingshot acceleration a
Page 108 and 109: Sailboats Smooth sailing RC sailboa
Page 110 and 111: GR2087 Graupner Ares 3 Scale R/C Ha
Page 112 and 113: SCALE SHIPS 34” long freighter is
Page 114 and 115: Sealed Lead Batteries for Scale R/C
Page 117: Customer Number (if known) Name Add
show all

2 - ClamSITel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?