2 - ClamSITel
2 - ClamSITel
2 - ClamSITel
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
82<br />
Ducted Fans<br />
55mm Ducted fan for Speed 280/300 and<br />
Brushless motors<br />
VAS055 Vasa Ducted Fan without Nacelle<br />
for Speed 280/300 ...................... $89.99<br />
Powerful carbon fiber mini fan for small ducted<br />
fan projects. Length 71mm (2-13/16"),<br />
Outside Diameter at front lip 64mm (2-1/2"),<br />
Inlet Diameter 55mm (2 3/16"), Outside<br />
Diameter of case 56mm (2-3/16"), Weight<br />
without motor 23 grams, comes complete with motor adapters for 2mm<br />
and 2.3mm shafts. Two M3 motor mount screws included.<br />
65mm Ducted Fan for Brushless Power<br />
It is possible to use this ducted fan in models<br />
which weigh up to 3 times more than the thrust<br />
(30 oz. airplane), however, the optimal ratio<br />
between thrust and total airplane weight is 1:2.<br />
This would be an airplane that weighed 20 oz..<br />
Duct and fan blades are made of rigid woven<br />
carbon fiber. Motor housing and stators are<br />
made of one continuous piece of woven carbon<br />
fiber for added strength.<br />
VAS400 Ducted Fan for 400/480 Motors .......................... $89.99<br />
Length is 75mm (2.95”), Outside diameter is 66mm (2.60”), Inside<br />
diameter is 65mm (2.56”). Weight without motor is 35 grams.<br />
VAS400G Ducted Fan for<br />
400/480 Motors with Nacelle ................................................ $119.99<br />
64mm fan unit with 2.3 and 3mm collet adapter<br />
FWF90210 64mm Ducted Fan Set<br />
........................................................... $11.99<br />
64mm interior diameter, 66mm exterior diameter,<br />
42mm long. 24mm diameter motor<br />
mount with internal steps for 20mm motor.<br />
Remove these steps for use with up to<br />
24mm dia. motor. Motor mount pattern is 4<br />
holes on 16mm centers. This is the replacement<br />
fan for our Su-34 and F-15 jets.<br />
Accepts the FWF90137 brushless Outrunner motor (sold separately).<br />
Includes collets for 2.3mm and 3mm shaft motors. Includes 4-2.5mm<br />
motor mount screws.<br />
NEW! 64mm Ducted Fan, 3500kv Outrunner Motor<br />
and 45A ESC<br />
FW3070 Complete Brushless Power System for Jets ......... $99.99<br />
Complete power solution for your 64mm<br />
jets. Includes a 64mm ducted fan,<br />
3500Kv Outrunner Brushless Motor and<br />
a 45A Brushless ESC with BEC, suitable<br />
for use with up to 4 lithium cells.<br />
Really bring out the performance of your<br />
jet. This power set produces about 490<br />
watts of power and has a thrust that<br />
exceeds 2.2 pounds. All this with an<br />
amp draw of approximately 33A. Motor<br />
comes pre-installed in the 64mm fan and pre-connected with 3.5mm<br />
connectors. The 45A ESC comes pre-connected with the matching<br />
3.5mm female connectors and the power wires are pre-connected with<br />
a genuine Deans Ultra male connector. ESC includes a BEC circuit<br />
5V/3A and weighs 63g (2.2 oz.).<br />
NEW! Add thrust vectoring to your jet<br />
FWF900111 180 Degree Vectored Thrust<br />
Nozzle Set ....................................... $12.99<br />
Single axis thrust vector unit with a total range<br />
of motion of about 40 degrees. Unit is made<br />
of injection molded plastic and is a ball and<br />
socket design with a molded foam exhaust<br />
nozzle trim ring. Inlet diameter is 62mm ID<br />
and outlet diameter is 60mm ID. The unit's<br />
diameter at the largest point is 82mm and the<br />
overall length is 84mm. Comes pre-assembled with a nylon control<br />
horn in place. Requires a micro servo to operate thrust vectoring (not<br />
included). Total range of motion requires approximately 28mm of<br />
pushrod travel.<br />
Electric Accessories<br />
Pre-wired components, Save<br />
soldering time and guesswork<br />
The battery packs,<br />
Jeti Motor<br />
Controller, charging<br />
wires, and motor<br />
hookup wires<br />
shown here all have<br />
Deans Ultra, Speed 400 or JST Connectors soldered in place on them.<br />
This saves you soldering time and also helps you to make correct connections<br />
when you’re hooking up or charging your system.<br />
PC001C Charger Wire with<br />
Speed 400 Connector and Banana Plugs ............................... $6.49<br />
BAT220 Charger Adapter, JST to Deans Ultra ........................ $4.99<br />
BAT221 Charger Adapter, JST to Speed 400 .......................... $6.49<br />
Useful for chargers that have JST connectors on the output.<br />
BAT225 Speed 400 Connector Lead .................................... $5.99<br />
A red and a black wire with Speed 400 connector in place. Can be<br />
used as a charging lead to battery packs for Speed 400 motor use.<br />
BAT226 13” Speed 400 Connector Lead ............................. $6.99<br />
13” yellow motor wires with Speed 400 connector soldered in place.<br />
Solder the wire ends to your motor. Use as motor leads to your speed<br />
control.<br />
BAT228 Connector Lead for<br />
Battery Packs with JST connectors ....................................... $2.99<br />
7” length. A red and black wire with JST mini connector which mates<br />
to battery packs with this type connector which is often used in micro<br />
electric helicopters. Use this as a charging lead or to connect a battery<br />
pack or motor to a speed controller.<br />
To 10 Amps:<br />
Excellent for electric<br />
Slowflyers<br />
DEA002 Deans 2 Pin<br />
Connectors, pair ............... $2.39<br />
DEA002P Deans 2 Pin Polarized Connectors, pair ............... $2.39<br />
DEA003 Deans 3 Pin Connectors, pair ............................... $2.39<br />
Tiny, light, reliable. Tighten the female connectors occasionally by<br />
inserting a pin in the outside of their sockets to force the two jaws<br />
together.<br />
Plug&Fly Connectors for Speed 400<br />
GR2978 MG-6 Male Connector ...... $2.89<br />
GR2979 MG-6 Female Connector .. $2.89<br />
The connectors used on<br />
battery and charger for<br />
micro helicopters<br />
BAT229 JST Connector and Wires,<br />
Battery Lead ................................................................................ $2.99<br />
7” length. This is normally used on slow flyer and micro electric aircraft<br />
battery packs and speed controllers for motor connection. Male<br />
plastic connector which mates to wire harness (pigtail) BAT228.<br />
BAT228 JST Connector and Wires, Charger Lead …................ $2.99<br />
7” length. This is normally used as a charging lead and on speed controllers<br />
and motors. Female plastic connector which mates to BAT229.<br />
To 20 Amps:<br />
Tiny Polarized connectors for Speed 400 use<br />
HLFK4003 Polarized Speed 400 Connectors,<br />
3 sets, red ................................................ $7.99<br />
1 Polarized Connector set consists of: 1 Red<br />
plastic holder with a single male and single<br />
female connector. Example: To connect a nicad<br />
pack to a battery charger you need 2 Polarized<br />
Connectors. Gold plated connectors. Tiny: the male connector is .86”<br />
long. The red plastic polarized holder is .98” long. One Polarized<br />
Connector set weighs 1.81 grams.<br />
HLFK4004 Polarized Speed 400 Connectors, 3 sets, Yellow ... $7.99<br />
Same as HLFK4003 but have yellow plastic polarized holders.<br />
HLFK4013 Polarized Speed 400 Connectors, 1 set, Red ........ $2.99<br />
HLFK4014 Polarized Speed 400 Connectors, 1 set, Yellow .... $2.99<br />
Your R/C Superstore • (866) 512-1444