2 - ClamSITel
2 - ClamSITel
2 - ClamSITel
- No tags were found...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Ball Links, Connectors, Clevises,<br />
Control Horns<br />
These oversize ball links are<br />
SAFER!<br />
Very large ball links 1” long. These are<br />
much safer for flight control uses than smaller types. These are also<br />
strong enough for use in steering linkages in RC cars and helicopter<br />
rotor control. 2-56 and 4-40 threaded rods will self-thread into the control<br />
rod end.<br />
HLH518 Oversize Ball Link, small stud ................................... $0.99<br />
HLH519 Oversize Ball Link, large stud ................................... $0.99<br />
Smaller Pushrod Connectors<br />
for Slow and Park Flyers<br />
MJ2765 Micro Pushrod<br />
Connectors, 6 ............. $4.99<br />
Overall length of each connector<br />
is only 5/16”. For easy adjustment<br />
of pushrods in small planes.<br />
Phillips set screw locks pushrod in<br />
place. Starlock holds connector in<br />
servo output wheel.<br />
Threaded<br />
Pushrod<br />
Connectors are<br />
safer and more<br />
adjustable than set-screw types.<br />
HLFK3061 Threaded Pushrod Connectors, 2-56, pack of 2 ...... $6.99<br />
Instead of clamping a pushwire to your servo output these are 2-56 threaded<br />
for max safety. The pin through the servo output arm is threaded and is held<br />
in place with a nut for removing and for relocating along the servo output arm.<br />
Move control<br />
surfaces accurately with<br />
no horns or pushrod<br />
showing!<br />
CH901 Hidden Control Horns, pair ............................................... $5.99<br />
7/8” wide, 1-1/8” long. Can be installed inside a wing, horizontal stab, or<br />
vertical fin to actuate, respectively, the ailerons and flaps, elevator, or rudder.<br />
Each package contains one left and one right actuator that move in<br />
opposite directions. There is almost no backlash or “slop”. Swivel ball links<br />
are included for hookup to your pushrod or cable ends.<br />
BIG control horns or fastening point<br />
for flying wires<br />
GR36764 Graupner Aluminum<br />
Control Horns, 5 ........... $14.99<br />
Can be used as control horns in<br />
a pull-pull system, or as hard<br />
points to attach wire bracing for<br />
wings or tail. Weigh less than 1<br />
gram each and are 7/32” dia. x<br />
5/16” long, with a 3/8” dia. reinforcing<br />
ring. Mounts thru the surface to be controlled, large glue surface<br />
provides solid installation. Threaded section has about 1/4” of<br />
adjustment and is pre-drilled for standard clevis.<br />
BIG control horns or fastening point<br />
for flying wires<br />
GR36763 Graupner<br />
Brass Control Horns,<br />
pk. of 5 .............................. $13.99<br />
Can be used as control horns in a<br />
pull-pull system, or as hard points to<br />
attach wire bracing for wings or tail.<br />
Adjustable. Weigh less than 3 grams each and are 1/4” dia. x 5/16”<br />
long, with a 1/2” dia. reinforcing ring. Large glue surface provides solid<br />
installation. Threaded section has about 1/4” of adjustment and is predrilled<br />
for standard clevis.<br />
Hardware, Tools and Miscellaneous<br />
Carbon Fiber Tubes, Rods and Strips<br />
The quickest and lightest way to increase strength in your model structures.<br />
Use the smallest of the carbon rods to brace the tails of your<br />
foam profile planes, or make up you own carbon pushrods from rod or<br />
tube. Add a length of carbon rod to the leading edge of your foam<br />
model to make it impervious to the dings that are common while landing.<br />
Laminate some carbon strip to the sides of a spar to make it radically<br />
stronger, but not a lot heavier. Can be glued with CA, epoxy or<br />
Graupner’s, GR959 “Uhu Por”.<br />
Carbon Fiber Tube, 1000mm long,<br />
O.D. x I.D. in mm<br />
GXT3012 3.0 x 1.2 ........... $2.90<br />
GXT3015 3.0 x 1.5 ........... $2.60<br />
GXT3020 3.0 x 2.0 ........... $2.20<br />
GXT3518 3.5 x 1.8 ........... $3.30<br />
GXT3520 3.5 x 2.0 ........... $3.30<br />
GXT3525 3.5 x 2.5 ........... $2.40<br />
GXT4020 4.0 x 2.0 ........... $4.40<br />
GXT4025 4.0 x 2.5 ........... $3.60<br />
GXT4030 4.0 x 3.0 ........... $2.70<br />
GXT4525 4.5 x 2.5 ........... $5.20<br />
GXT4535 4.5 x 3.5 ........... $3.40<br />
GXT5030 5.0 x 3.0 ........... $5.40<br />
Carbon Fiber Square Tube,<br />
1000mm long, outside dim. x<br />
inside dim. in mm<br />
GXQ4030 4.0 x 3.0 ................. $5.90<br />
GXQ8070 8.0 x 7.0 ................. $9.60<br />
Carbon Fiber Rod, 1000mm long,<br />
O.D. in mm<br />
GXR10 1.0 ........................ $1.30<br />
GXR12 1.2 ........................ $1.30<br />
GXR13 1.3 ........................ $1.30<br />
GXR15 1.5 ........................ $1.30<br />
GXR16 1.6 ........................ $1.40<br />
GXR18 1.8 ........................ $1.40<br />
GXR20 2.0 ........................ $1.70<br />
GXR25 2.5 ........................ $2.20<br />
Metric Sizes, Brass tubing, music wire<br />
Metric Brass Tubing,<br />
9-1/2" long<br />
Useful for bushings, adapting metric diameters to USA, making metric drilled<br />
wheels fit USA dimension axles. These accurately telescope into each other,<br />
and fit accurately over the metric music wire.<br />
Metric Music Wire,<br />
9-1/2" long<br />
For bearings, adapting to<br />
metric tubing. Use the less<br />
expensive USA sizes for<br />
large or long things like landing<br />
gears, pushwires.<br />
Metric Threaded<br />
Rods, 9-1/2" long<br />
Mild steel with zinc plating.<br />
Fully threaded.<br />
GXT5040 5.0 x 4.0 ........... $3.40<br />
GXT5532 5.5 x 3.2 ........... $6.80<br />
GXT5535 5.5 x 3.5 ........... $6.20<br />
GXT5540 5.5 x 4.0 ........... $5.30<br />
GXT5842 5.8 x 4.2 ........... $5.70<br />
GXT5845 5.8 x 4.5 ........... $5.20<br />
GXT6030 6.0 x 3.0 ........... $9.20<br />
GXT6040 6.0 x 4.0 ........... $6.60<br />
GXT6050 6.0 x 5.0 ........... $4.60<br />
GXR30 3.0 ........................ $3.20<br />
GXR35 3.5 ........................ $4.10<br />
GXR40 4.0 ........................ $5.60<br />
GXR45 4.5 ........................ $6.90<br />
GXR50 5.0 ........................ $8.70<br />
Carbon Fiber Strips, 1000mm long, thickness x width in mm<br />
GXS1030 1.0 x 3.0 ............... $2.80<br />
GXS1040 1.0 x 4.0 .............. $3.40<br />
GXS0510 0.5 x 10.0 ............ $4.30<br />
GXS0825 0.8 x 25.4 .......... $10.60<br />
Stock No: OD (mm) ID (mm) Price:<br />
HLRE0500 ......... 2 ......... 1.6......... $0.99<br />
HLRE0501 ......... 3 ......... 2.1......... $1.99<br />
HLRE0502 ......... 4 ......... 3.1......... $1.99<br />
HLRE0503 ......... 5 ......... 4.1......... $1.99<br />
HLRE0504 ......... 6 ......... 5.1......... $1.99<br />
Stock No: Diameter (mm): Price:<br />
HLRE0521 ......... 1.0 ................ $0.99<br />
HLRE0522 ......... 1.5 ................ $0.99<br />
HLRE0523 ......... 2.0 ................ $0.99<br />
HLRE0524 ......... 3.0 ................ $0.99<br />
HLRE0525 ......... 4.0 ................ $0.99<br />
HLRE0526 ......... 5.0 ................ $1.99<br />
Stock No: Thread size (mm): Price:<br />
HLRE0540 ............ M2 ................ $2.99<br />
HLRE0541 ......... M2.5 ................ $2.99<br />
HLRE0542 ............ M3 ................ $2.99<br />
HLRE0543 ............ M4 ................ $2.99<br />
www.hobby-lobby.com • Order Online 24/7 97