Tail Rotor Driveshaft Hanger

More documents

Recommendations

Info

BHT-212-CR&ON7 U----HANGER-204-040-604-005 COUPLINGREFr-i P-16000-1 TEMP-PLATE (RED BORDER)2 REQD-180 DEGREES APARTEQUALLY SPACED WITHIN 0.3 IN. (7.62 mm)IDENTIFICATIONPLATE0.74± 0.030 IN.(18.79±0.762 mm)212-R-65-5Figure 65-5.<strong>Tail</strong> rotor driveshaft coupling TEMP-PLATES installation65-00-00Page 16Rev.3
B HT-212-CR&0INTERMEDIATE (42°) GEARBOX65-11. INTERMEDIATE (42°) GEARBOX.65-12. DELETED65-13. Disassembly.NUMBERT1013080T101350SPECIAL TOOLS REQUIREDNOMENCLATUREJackscrewBacklash clampT102030-3 Backlash clamp204- 040- 001 -17 Puller tool (Sightglass)PAT-5Sor Equivalent2. Release pin (24) which secures chain tocase and remove cap (26). Remove packing(25) from cap. Discard packing.r:-.,-a)^N-03. Remove retainer ring (19), glass (21),and indicator (22). Use suitable tool toremove glass. Carefully remove packing (20)from glass. Discard packing.
Page 1 and 2: BHT-212-CR&0CHAPTER 65 - TAIL ROTOR
Page 3 and 4: BHT-212-CR&0CONSUMABLE MATERIAL LIS
Page 5 and 6: BHT-212-CR&OTAIL ROTOR DRIVE SYSTEM
Page 7 and 8: BHT-212-CR&OTAIL ROTOR DRIVESHAFT H
Page 9: BHT-212-CR&O,..:+3NOTEIf TEMP-PLATE
Page 12 and 13: BHT-212-CR&0(b-n--1 0-ca0)0ohm^mNOT
Page 14 and 15: BHT-212-CR&O--{-gym2 CAUTIONIN ORDE
Page 16 and 17: mI-:BHT-212-CR&O15INTERNAL SPLINESI
Page 18 and 19: BHT-212-CR&OA Acceptable pattern ty
Page 22 and 23: BHT-212-CR&0I65-14. Cleaningmm300MA
Page 25 and 26: BHT-212-CR&O1. Output quill2. Nut3.
Page 27: BHT-212-CR&0Required dimensions sha
Page 30 and 31: BHT-212-CR&O.w.212-040-506-1 CASE A
Page 33 and 34: BHT-212-CR&0(3) Grind new blank shi
Page 35 and 36: BHT-212-CR&010. Prepare data plate
Page 37 and 38: cBHT-212-CR&02. Hold outer coupling
Page 39 and 40: BHT-212-CR&0SEAL (13) PARTIALLY SEA
Page 41: BHT-212-CR&0000000)0)0)1a. Inspect
Page 44 and 45: BHT-212-CR&O711140,a11 1e9ITEM NOME
Page 46 and 47: BHT-212-CR&OTOPHEEL TOPHEEL i \ TOE
Page 48 and 49: .-.BHT-212-CR&ONOTES7. Unacceptable
Page 50 and 51: BHT-212-CR&OACCEPTABLE212-R-65-14UN
Page 52 and 53: BHT-212-CR&ONUMBERT101307T101333T10
Page 55 and 56: BHT-212-CR&065-29. OUTPUT QUILL.65-
Page 57: 0BHT-212-CR&O5. Perform magnetic pa
Page 60 and 61: BHT-212-CR&0SEAL (13) PARTIALLY SEA
Page 62 and 63: 0BHT-212-CR&010. Inspect sleeves (2
Page 64 and 65: B HT-212-C R &06. Repair inner coup
Page 66 and 67: BHT-212-CR&O-4CAUTIONto 203.37 Nm)
Page 69 and 70: BHT-212-CR&OTAIL ROTOR(90°) GEARBO
Page 71:
BHT-212-CR&O4. Remove sealant from
Page 74 and 75:
0BHT-212-CR&O1. Shaft 13. Stud 25.
Page 77 and 78:
BHT-212-CR&07. Inspect following pa
Page 79 and 80:
*l.l-.BHT-212-CR&011 13MIN.MAXITEM
Page 81 and 82:
B HT-212-CR&0ACCEPTABLE WEAR PATTER
Page 83 and 84:
BHT-212-CR&015. Repair or replace s
Page 85 and 86:
BHT-212-CR&ODIAMETER A(SEAL CONTACT
Page 87 and 88:
BHT-212-CR&OSPECIAL TOOLS REQUIRED
Page 89 and 90:
BHT-212-CR&Oa. Cap adapter (10, fig
Page 91 and 92:
BHT-212-CR&OSEE DETAIL B16INSTALL W
Page 93:
BHT-212-CR&O-48. Inspect outer coup
Page 96 and 97:
BHT-212-CR&OA Acceptable pattern ty
Page 98 and 99:
BHT-212-CR&ON^D--I--DOff'0(DD)j"'ZZ
Page 100 and 101:
BHT-212-CR&0Table 65-1. Magnetic Pa
Page 102 and 103:
BHT-212-CR&0Table 65-1.Magnetic Par
show all

Tail Rotor Driveshaft Hanger

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?