Tail Rotor Driveshaft Hanger

More documents

Recommendations

Info

BHT-212-CR&O3. Remove inner and outer couplings (10and 11) from pinion.4. Separate couplings and remove seal (13)from outer coupling.5. Hold sleeve (20) with T101560 holdingfixture and use T101600 wrench to removenut (15). Remove seal (14) and packing (16)from nut.3(n,O 030(
BHT-212-CR&OSEE DETAIL B16INSTALL WEAR SLEEVE WITHROUNDED END AS SHOWNDETAIL A 4221. Ring retaining 9. Washer 17. Spacer2. Plate 10. Coupling, inner 18. Sleeve, wear3. Spring centering 11. Coupling, outer 19. Bearing duplex4. Spring lock 12. Deleted 20. Sleeve5. Spacer 13. Seal 21. Pinion6. Retainer 14. Seal 22. Cork plug7. Packing 15. Nut8. Bolt 16. PackingUuaNOTESA Location of temperature indicator TEMP-PLATE.A Apply adhesive sealant (C-308) on nut (15) and sleeve (20) after assembly.Figure 65-28. <strong>Tail</strong> rotor gearbox input quill (sheet 1 of 2)212-R-65-28-1212-040-004-1165-00-00Rev. 3 Page 73
Page 1 and 2:
BHT-212-CR&0CHAPTER 65 - TAIL ROTOR
Page 3 and 4:
BHT-212-CR&0CONSUMABLE MATERIAL LIS
Page 5 and 6:
BHT-212-CR&OTAIL ROTOR DRIVE SYSTEM
Page 7 and 8:
BHT-212-CR&OTAIL ROTOR DRIVESHAFT H
Page 9:
BHT-212-CR&O,..:+3NOTEIf TEMP-PLATE
Page 12 and 13:
BHT-212-CR&0(b-n--1 0-ca0)0ohm^mNOT
Page 14 and 15:
BHT-212-CR&O--{-gym2 CAUTIONIN ORDE
Page 16 and 17:
mI-:BHT-212-CR&O15INTERNAL SPLINESI
Page 18 and 19:
BHT-212-CR&OA Acceptable pattern ty
Page 20 and 21:
BHT-212-CR&ON7 U----HANGER-204-040-
Page 22 and 23:
BHT-212-CR&0I65-14. Cleaningmm300MA
Page 25 and 26:
BHT-212-CR&O1. Output quill2. Nut3.
Page 27:
BHT-212-CR&0Required dimensions sha
Page 30 and 31:
BHT-212-CR&O.w.212-040-506-1 CASE A
Page 33 and 34:
BHT-212-CR&0(3) Grind new blank shi
Page 35 and 36:
BHT-212-CR&010. Prepare data plate
Page 37 and 38:
cBHT-212-CR&02. Hold outer coupling
Page 39 and 40: BHT-212-CR&0SEAL (13) PARTIALLY SEA
Page 41: BHT-212-CR&0000000)0)0)1a. Inspect
Page 44 and 45: BHT-212-CR&O711140,a11 1e9ITEM NOME
Page 46 and 47: BHT-212-CR&OTOPHEEL TOPHEEL i \ TOE
Page 48 and 49: .-.BHT-212-CR&ONOTES7. Unacceptable
Page 50 and 51: BHT-212-CR&OACCEPTABLE212-R-65-14UN
Page 52 and 53: BHT-212-CR&ONUMBERT101307T101333T10
Page 55 and 56: BHT-212-CR&065-29. OUTPUT QUILL.65-
Page 57: 0BHT-212-CR&O5. Perform magnetic pa
Page 60 and 61: BHT-212-CR&0SEAL (13) PARTIALLY SEA
Page 62 and 63: 0BHT-212-CR&010. Inspect sleeves (2
Page 64 and 65: B HT-212-C R &06. Repair inner coup
Page 66 and 67: BHT-212-CR&O-4CAUTIONto 203.37 Nm)
Page 69 and 70: BHT-212-CR&OTAIL ROTOR(90°) GEARBO
Page 71: BHT-212-CR&O4. Remove sealant from
Page 74 and 75: 0BHT-212-CR&O1. Shaft 13. Stud 25.
Page 77 and 78: BHT-212-CR&07. Inspect following pa
Page 79 and 80: *l.l-.BHT-212-CR&011 13MIN.MAXITEM
Page 81 and 82: B HT-212-CR&0ACCEPTABLE WEAR PATTER
Page 83 and 84: BHT-212-CR&015. Repair or replace s
Page 85 and 86: BHT-212-CR&ODIAMETER A(SEAL CONTACT
Page 87 and 88: BHT-212-CR&OSPECIAL TOOLS REQUIRED
Page 89: BHT-212-CR&Oa. Cap adapter (10, fig
Page 93: BHT-212-CR&O-48. Inspect outer coup
Page 96 and 97: BHT-212-CR&OA Acceptable pattern ty
Page 98 and 99: BHT-212-CR&ON^D--I--DOff'0(DD)j"'ZZ
Page 100 and 101: BHT-212-CR&0Table 65-1. Magnetic Pa
Page 102 and 103: BHT-212-CR&0Table 65-1.Magnetic Par
show all

Tail Rotor Driveshaft Hanger

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?