Tail Rotor Driveshaft Hanger

More documents

Recommendations

Info

....BHT-212-CR&0MIN.MAXITEM NOMENCLATURE INCHES mm INCHES mm_CD- --_. -(l).oNE E EE E EN00 00wEo
Page 1 and 2:
BHT-212-CR&0CHAPTER 65 - TAIL ROTOR
Page 3 and 4:
BHT-212-CR&0CONSUMABLE MATERIAL LIS
Page 5 and 6:
BHT-212-CR&OTAIL ROTOR DRIVE SYSTEM
Page 7 and 8:
BHT-212-CR&OTAIL ROTOR DRIVESHAFT H
Page 9:
BHT-212-CR&O,..:+3NOTEIf TEMP-PLATE
Page 12 and 13:
BHT-212-CR&0(b-n--1 0-ca0)0ohm^mNOT
Page 14 and 15:
BHT-212-CR&O--{-gym2 CAUTIONIN ORDE
Page 16 and 17:
mI-:BHT-212-CR&O15INTERNAL SPLINESI
Page 18 and 19:
BHT-212-CR&OA Acceptable pattern ty
Page 20 and 21:
BHT-212-CR&ON7 U----HANGER-204-040-
Page 22 and 23:
BHT-212-CR&0I65-14. Cleaningmm300MA
Page 25 and 26:
BHT-212-CR&O1. Output quill2. Nut3.
Page 27:
BHT-212-CR&0Required dimensions sha
Page 30 and 31:
BHT-212-CR&O.w.212-040-506-1 CASE A
Page 33 and 34:
BHT-212-CR&0(3) Grind new blank shi
Page 35 and 36:
BHT-212-CR&010. Prepare data plate
Page 37 and 38:
cBHT-212-CR&02. Hold outer coupling
Page 39 and 40:
BHT-212-CR&0SEAL (13) PARTIALLY SEA
Page 41:
BHT-212-CR&0000000)0)0)1a. Inspect
Page 44 and 45: BHT-212-CR&O711140,a11 1e9ITEM NOME
Page 46 and 47: BHT-212-CR&OTOPHEEL TOPHEEL i \ TOE
Page 48 and 49: .-.BHT-212-CR&ONOTES7. Unacceptable
Page 50 and 51: BHT-212-CR&OACCEPTABLE212-R-65-14UN
Page 52 and 53: BHT-212-CR&ONUMBERT101307T101333T10
Page 55 and 56: BHT-212-CR&065-29. OUTPUT QUILL.65-
Page 57: 0BHT-212-CR&O5. Perform magnetic pa
Page 60 and 61: BHT-212-CR&0SEAL (13) PARTIALLY SEA
Page 62 and 63: 0BHT-212-CR&010. Inspect sleeves (2
Page 64 and 65: B HT-212-C R &06. Repair inner coup
Page 66 and 67: BHT-212-CR&O-4CAUTIONto 203.37 Nm)
Page 69 and 70: BHT-212-CR&OTAIL ROTOR(90°) GEARBO
Page 71: BHT-212-CR&O4. Remove sealant from
Page 74 and 75: 0BHT-212-CR&O1. Shaft 13. Stud 25.
Page 77 and 78: BHT-212-CR&07. Inspect following pa
Page 79 and 80: *l.l-.BHT-212-CR&011 13MIN.MAXITEM
Page 81 and 82: B HT-212-CR&0ACCEPTABLE WEAR PATTER
Page 83 and 84: BHT-212-CR&015. Repair or replace s
Page 85 and 86: BHT-212-CR&ODIAMETER A(SEAL CONTACT
Page 87 and 88: BHT-212-CR&OSPECIAL TOOLS REQUIRED
Page 89 and 90: BHT-212-CR&Oa. Cap adapter (10, fig
Page 91 and 92: BHT-212-CR&OSEE DETAIL B16INSTALL W
Page 93: BHT-212-CR&O-48. Inspect outer coup
Page 97 and 98: BHT-212-CR&O1. Replace parts which
Page 99 and 100: BHT-212-CR&0of retainer does not al
Page 101 and 102: BHT-212-CR&O-4Table 65-1. Magnetic
Page 103: -
show all

Tail Rotor Driveshaft Hanger

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?